Information Signs; Technical Data; General; Box Column Fastening - haacon DKV550/1300 Manuel D'utilisation

Additional instructions to be adhered to:
– German Industrial Health and Safety Ordinance (BetrSichV).
– Country-specific regulations.
– German Accident prevention regulations (DGUV-V 54).
– Operating instructions for the attached rope winch/chain hoist.

3. infOrMAtiOn SignS

Pay attention to the load specifications of the boom and tightening
torque of the bolts for the winch.
cAutiOn!
The permissible load is determined by the support structure,
not by the permissible load of the attached winch / hoist. If the
load gets jammed or caught on something, halt the lifting (or
lowering) operation immediately. Otherwise you risk overloa-
ding the support structure.
first rectify the malfunction, then proceed with the task!

4. technicAl dAtA

crane with hoist
dKV...
dKe...
Max. perm. load kg
Minimum load kg
Crank force N
Lift / crank rotation mm
Load rope length m
Load rope ø mm
Construction
Rope strength N/mm
Material
Weight (crane) kg
Weight (boom) kg
Torque for swivelling Nm
Working temperature °C
– without hoist
dKV...
dKe...
Max. perm. load kg
Weight (crane) kg
Weight (boom) kg
Torque for swivelling Nm
Working temperature °C
Modifications of the design and execution reserved.
For customized products, the data of the enclosed drawing is valid.
The following receptacles may be used:
DKBV - DKWV - DKBE - DKWE
094325_h_de_gb_fr_es_pt_it_nl_drehkr_s
550/ 360/ 360/ 250/
1300 1500 2000 2000
550 360 250
50
100 145 100
16 46
12
6 5
7 x 19 / 6 x 19 SE / 6 x 19 IWRC
1570
2
1.4401
46
30 20 23 23
275
-20 ... +50
550/ 360/ 360/ 250/
1300 1500 2000 2000
550 360 250
46
14 17
275
-20 ... +50
haacon hebetechnik gmbh – Telefon +49 (0) 9375 - 84-0 – Fax +49 (0) 9375 - 8466
ce conformity
The Declaration of Conformity is only valid, if cranes and
columns specified here are used. The columns must be must
be mounted according to the specifications in this manual.
The Declaration of Conformity applies to lifting devices, which
belong to the scope of delivery.

5. generAl

The swivel jib crane is a steel construction with variable overhang.
The permissible payload is identical for all pinning positions of the pul-
ley. It is inserted into a box column, which can be attached to the
ground or to the basin edge, and serves for lifting and lowering, as well
as swivelling loads, predominantly in sewage treatment plants.
Manually operated chain hoists or galvanised respectively stainless
steel rope winches are used as hoisting gears.
The crane complies with lifting class H1 from DIN 15018 and is suited
for a total of load changes < 2 x 10

6. BOx cOluMn fAStening

The box columns must be attached sufficiently and according to the
following regulations. The specifications for mounting the box column
and specifications for embedding the box columns in concrete can be
inferred from the drawings (item 12).
The operator and/or the company assigned by him for carrying out
the mounting are responsible for this. The correct construction of the
mounting must be confirmed (e.g. with mounting protocol).
6.1 ground, wall mounting with shear connectors
Basis for dimensioning the anchorage is the „Guideline for the Europe-
an Technical Approval of Metal Anchors for use in Concrete", Appendix
C, technology A, for bonded anchors. They are subject on-site to the
responsibility of an engineer having experience of anchorages and
concrete construction.
the following must be observed:
– Impacts and vibrations are inadmissible.
– Anchors are approved for use indoors and for use outdoors,
if no particularly aggressive conditions are present, e.g.:
– Spraying zone of sea water, constant, alternating immersion
in sea water
– Chloric atmospheres, e.g. in indoor swimming pools
– Extreme chemical contaminations, e.g. such as
– in flue gas desulphurating plants
– Anchors may be set in dry and wet concrete, however not in
boreholes filled with water
– Overhead assembly is inadmissible
– The temperature range for use of the anchorages is enc-
losed: 40 °C to +50 °C (max. long-term temperature) to
+80 °C (max. short-term temperature).
The shear connectors must be selected with consideration to the lar-
gest permissible load, with the greatest possible overhang of the crane
for the shear connector system according to approval (ETA-05/0231:
MKT V A4).
6.2 Concrete/Underground
– unripped concrete (pressure zone)
– C20/24 (B25) ≤ Concrete strength class ≤ C50/60 after EN
206:2000-12
– Normal or without reinforcement, without edge reinforcement
– Perfect compression, no significant cavities
– Minimum concrete thickness: 175 mm
Geometrical characteristic values
– Minimum distance to each concrete edge: 100mm
– Minimum distance between the shear connectors according to re-
quirements of the mounting holes and/or after drawing (s. point 12)
Packing, transport, storage
The glass cartridges must be protected against sun exposure and be
stored in a dry place according to the assembly instructions at tempe-
ratures of at least +5 °C to at the most +25 °C.
Glass cartridges with exceeded date of expiry may not be used
anymore. The anchors must be packed and supplied as a mounting unit.
The glass cartridges are packed separately from the anchor rods (inclu-
ding hexagon nuts and washers). The glass cartridges V-P may only be
used with the appropriate anchor rods V-A A4.
6.3 generally the following applies:
– The anchors selected by haacon do not replace having the
dimensioning examined by a stress analyst according to the
local operating conditions.
– All other fastenings (selection, dimensioning, design) are
the sole responsibility of the operator, and/or of the compa-
ny assigned by him.
4 .
7
gB