Locating A Track (Ams/Direct Access); Locating A Point (Shuttle Play/Mark&Locate) - Sony PCM-R500 Mode D'emploi

Locating a Track (AMS*/Direct
Access)
You can locate the tracks in a number of ways, but only
after you have recorded start IDs on the tape (see pages
19 to 23). To use Direct Access, program numbers
must be recorded on the tape (see pages 19 and 23).
PREVIOUS =/NEXT + PLAY (
POWER
Ø ON ø OFF
REMOTE
WIRED OFF WIRELESS
AMS
PREVIOUS NEXT
= +
PHONE LEVEL
• START ID
OPEN/CLOSE STOP
AUTO REHEARSAL WRITE ERASE REPEAT LOCATE
6
MIN MAX
SKIP ID
PHONES
RENUMBER REHEARSAL WRITE ERASE SKIP PLAY MARK
To locate Do the following:
The beginning of the next Press NEXT + as many times
or succeeding tracks as you want while playing. For
(AMS) example, to locate the second
track ahead, press twice.
The beginning of the Press PREVIOUS = once
current track (AMS) while playing.
The beginning of Press PREVIOUS = as many
preceding tracks (AMS) times as you want while playing.
For example, to locate the second
track behind, press three times.
1 While the deck is playing or
By specifying the
stopped, turn DATA on the
program number of a
front panel until the program
track (Direct Access)
number you want appears in
the display (or enter the
program number with the
number buttons on the remote).
2 Press PLAY (.
* AMS = Automatic Music Sensor
z
If you enter the wrong program number during
Direct Access
If you haven't pressed the PLAY ( button, turn the
DATA dial on the deck (or press the CLEAR button,
then enter the correct number on the remote).
z
If the deck detects a blank section of 9 seconds or
more, end ID, or the end of the tape
The deck rewinds the tape automatically to its
beginning and stops (Auto Rewind).
z
You can make the deck start playing automatically
from the beginning of the tape after rewinding
(Auto Play)
Press the PLAY ( button while holding down the
REW 0 button.
INPUT
ANALOG DIGITAL
MODE
ANALOG INPUT
UNBALANCE BALANCE
COUNTER RESET
REC MODE
STANDARD LONG
MARGIN RESET
48k 44.1k
SBM
OFF ON
SHUTTLE DATA
REW FF REC MUTE MENU
REC LEVEL
R CH-1(L)
0 ) r
•
PLAY PAUSE REC
SET
0 10
p ( P r
CH-2(R)
•
0 10
DATA
Advanced Playback Operations
Locating a Point (Shuttle Play/
Mark & Locate)
You can locate a specific point by playing back at a
different speed or recording the absolute time code at
the point to be located later.
POWER
Ø ON ø OFF
REMOTE
WIRED OFF WIRELESS
PREVIOUS
=
PHONE LEVEL
•
START ID OPEN/CLOSE
AUTO REHEARSAL WRITE ERASE REPEAT LOCATE
6
MIN MAX
SKIP ID
PHONES RENUMBER REHEARSAL WRITE ERASE SKIP PLAY MARK
LOCATE MARK
To locate Do the following:
While the deck is playing, stopped,
A track using variable
or paused, turn SHUTTLE.
speed play (Shuttle Play)
• If the deck was playing or
stopped, the deck starts to play
when you release the SHUTTLE
dial.
• If the deck was paused, the deck
pauses when you release the
SHUTTLE dial.
1 While the deck is playing or
A particular point on a
stopped, press MARK. The
tape (Mark & Locate)
absolute time of the point
where you pressed the button
appears and flashes three
times.
2 Press LOCATE. The deck
locates the point and stops.
z
Playback speed during Shuttle Play
During Shuttle Play, you can vary the playback speed
from ±0.5 to ±8 times the normal playback speed (or ±1
to ±8 times the normal playback for material recorded
in long-play mode), depending on the angle and
direction of the SHUTTLE dial. Turn the dial clockwise
for forward playback or counterclockwise for reverse
playback.
The playback speed will be ±8 times normal speed
playback when you turn the dial to the left or right
fully.
Note
Shuttle Play should be used only when necessary since
prolonged use may damage the tape and drum.
z
The point memorized using the Mark & Locate
function will be erased when:
— you take out the cassette.
— you turn off the deck.
INPUT
ANALOG DIGITAL
MODE
ANALOG INPUT
UNBALANCE BALANCE
COUNTER RESET
REC MODE
STANDARD LONG
MARGIN RESET
48k 44.1k
SBM
OFF ON
SHUTTLE DATA
AMS
NEXT REW FF REC MUTE MENU
REC LEVEL
+ 0 ) R r CH-1(L)
•
STOP PLAY PAUSE REC
SET
0 10
p ( P r
CH-2(R)
•
0 10
SHUTTLE
3-859-278-12(1)
17 EN