Specifications - Sony PCM-R500 Mode D'emploi

Additional Information

Specifications

Recording section
Tape
Recording head
Recording time
Tape speed
Drum rotation
Error correction
Tape section
Track pitch
Sampling frequency
Modulation system
Transfer rate
Number of channels
D / A conversion
(quantization)
General section
Power requirements
Where purchased
U.S.A./Canada
Europe/U.K
Power consumption
Dimensions
Weight
Remote commander RM-D757 (supplied)
Remote control system
Power requirements
Dimensions
Weight
Input connectors
Analog Input
Connector Type
ANALOG Phono-
(UNBALANCE) plug jack
ANALOG XLR-3
(BALANCE) (FEMALE)
32 EN
Digital audio tape
Rotary head
Standard: 120 minutes
Long-play: 240 minutes
(DT-120)
Standard: 8.15 mm/s
Long-play: 4.075 mm/s
Standard: 2,000 rpm
Long-play: 1,000 rpm
Double-encoded Reed Solomon code
13.6 µm (20.4 µm)
48 kHz, 44.1 kHz, 32 kHz
8-10 modulation
2.46 Mbit/sec
2 channels, stereo
Standard: 16-bit linear
Long-play: 12-bit non-linear
Power requirements
120 V AC, 60 Hz
230 V AC, 50/60 Hz
PCM-R500: 34W
PCM-R700: 34W
Approx 482 × 145 × 355 mm (w/h/d)
(19 × 5 × 14 inches)
3 /
4
(not including rack mount adaptor)
PCM-R500: Approx 7.2kg (15 lb 14 oz)
PCM-R700: Approx 7.3kg (16 lb 2 oz)
Infrared control
3V DC, with two size-AA (R6) batteries
Approx 45 × 210 × 26 mm (w/h/d)
× 8 × 1
(1 13 / 3 / 1 / inches)
16 8 16
Approx 100g (3.5 oz) incl. batteries
Input impedance Rated input level
47 kilohms –12 dBs
10 kilohms +4 dBs
or more (factory setting)
(balanced)
Digital Input
Connector Type
AES/EBU
XLR-3
(FEMALE)
COAXIAL
Phono-plug
jack
Output connectors
Analog Output
Connector
Type
ANALOG
Phono-plug
(UNBALANCE)
jack
ANALOG
XLR-3
(BALANCE)
(MALE)
Stereo phone-
PHONES
plug jack
Digital Output
Connector Type
AES/EBU XLR-3
(MALE)
COAXIAL
Phono-plug
jack
Variable range of analog (BALANCE) input/output reference level
Maximum analog (BALANCE) output level
Remote switch connectors
Audio characteristics
Frequency response b)
Signal-to-noise ratio b)
Total harmonic distortion b)
a)
Wow and flutter
a) The reference level corresponds to –20 dB on the peak
level meters.
b) During analog input with the SBM function off
Supplied accessories
Design and specifications are subject to change without
notice.
Input impedance Rated input level
110
ohms
—
(balanced)
0.5 Vp-p
75 ohms
Output Rated Load
impedance output impedance
level a)
1 kilohm –12 dBs 47 kilohms
10 kilohms
+4 dBs
100 ohms
or more
(factory
(balanced)
setting)
100 ohms 0.36 mW 32 ohms
Output Load
Rated
impedance impedance
output
level
110 ohms
—
35 ohms
(balanced)
75 ohms 0.5 Vp-p 75 ohms
+4 dBs to –12 dBs
+24 dBs
DIN connector (8-pin, parallel)
Monaural minijack (serial)
Standard: 20-20,000 Hz (±0.5 dB)
Long-play: 20-14,500 Hz (±0.5 dB)
90 dB or more (20 kHz LPF, A-
Weight filter ON)
Standard: 0.05% or less
Long-play: 0.3% or less
(1 kHz, Reference level a) 20 kHz
LPF ON)
Below measurable limit (±0.001%
W.PEAK)
See page 4.
3-859-278-11(1)
a)