Menu Operations; Making Menu Settings - Sony PCM-R500 Mode D'emploi

Menu Operations

Menu Operations
Menu Operations
You can make various settings through menu
operations. Settings made through menu are
memorized even when the deck is turned off.
Note
You can do menu operations only when the deck is empty,
stopped or paused.
POWER
Ø ON ø OFF
REMOTE
WIRED OFF WIRELESS
PHONE LEVEL
•
START ID
AUTO REHEARSAL WRITE ERASE REPEAT
MIN MAX
SKIP ID
PHONES
RENUMBER REHEARSAL WRITE ERASE SKIP PLAY

Making menu settings

1
Press MENU.
The MENU button lights up.
2
Turn SHUTTLE to select the menu.
3
Turn DATA to select the parameter.
The selected parameter flashes.
When the parameter settings are "on" and "--" (off)
Turn the DATA dial clockwise to select "on" or
counterclockwise to select "--" (off).
4
Press SET.
The selected setting lights up.
5
Press MENU again.
The lit button goes off and the deck becomes
ready for operation.
Menu descriptions
A brief explanation is given below for each menu,
including their settings or setting range, factory setting,
and reference pages.
SET ID6
Selects the copy information to be written on the tape when
recording from the ANALOG(BALANCE/UNBALANCE)
IN connectors or the DIGITAL AES/EBU IN connector.
Settings: 00 (copying permitted), 10 (copying
prohibited), 11 (one generation copy only)
Factory setting: 00
Reference page: 6
EN
24
MENU SHUTTLE
INPUT
ANALOG DIGITAL
MODE
ANALOG INPUT
UNBALANCE BALANCE
COUNTER RESET
REC MODE
STANDARD LONG
MARGIN RESET
48k 44.1k
SBM
OFF ON
SHUTTLE DATA
AMS
PREVIOUS NEXT REW FF REC MUTE MENU
REC LEVEL
CH-1(L)
= + 0 ) R r
•
OPEN/CLOSE STOP PLAY PAUSE REC
LOCATE
SET
0 10
6 p ( P r
CH-2(R)
•
MARK
0 10
SET DATA
REC MUTE (RECord MUTE duration)
Sets the duration if the blank space created between tracks
by the Record Muting function.
Setting range: 0.5 to 9.5 seconds (in units of 0.5 second)
Factory setting: 4 seconds
Reference page: 14
L-SY TH (Level-SYnc THreshold)
Sets the reference input level for automatic writing of start
IDs.
Setting range: –12 to –60 dB (in units of 1 dB)
Factory setting: –45 dB
Reference page: 20
L-SY BK (Level-SYnc BlanK time)
Sets the length of time that the input signal must remain
below the reference level before automatic writing of start
IDs begin.
Setting range: 1 to 10 seconds (in units of 1 second)
Factory setting: 3 seconds
Reference page: 20
IEC S-ID (IEC Start-ID)
Specifies if start IDs (or skip IDs) are automatically detected
and written on the tape when recording from a DAT deck
connected to the DIGITAL COAXIAL IN connector.
Settings: on (start IDs (or skip IDs) are automatically
detected and written),
-- (writing of the start IDs (or skip IDs) is
determined by the settings of the L-SY TH
and L-SY BK menus)
Factory setting: on
Reference page: 7
IEC CD-Q (IEC CD-Q code)
Specifies if start IDs are written automatically whenever a Q
code defined by the user's bits on the CD is detected while
recording from a CD player connected to the DIGITAL
COAXIAL IN connector.
Settings: on (a Q code is detected and written as a
start ID automatically),
-- (writing of the start IDs is determined
by the settings of the L-SY TH and L-SY BK
menus)
Factory setting: on
Reference page: 7
AES S-ID (AES Start-ID)
Specifies if start IDs (or skip IDs) are automatically
detected and written on the tape when recording from
a DAT deck (for broadcast use) connected to the
DIGITAL AES/EBU IN connector, and if start IDs (or
skip IDs) are output through the DIGITAL AES/EBU
OUT connector.
Settings: on (start IDs (or skip IDs) are detected and
written automatically/start IDs (or skip IDs)
are output),
-- (writing of start IDs (or skip IDs) is
determined by the settings of th L-SY TH and
L-SY BK menus/start IDs (or skip IDs) are not
output)
Factory setting: --
Reference page: 7
3-859-278-11(1)