Transportation And Storage - Ryobi RCS3835T Traduction Des Instructions Originales

Limbing a tree
See page 280.
Limbing is removing the branches from a fallen tree. When
limbing leave larger lower limbs to support the log off the
ground. Remove the small limbs in one cut. Branches
under tension should be cut from the bottom up to avoid
binding the product.
Cutting springpoles
See page 280.
A springpole is any log, branch, rooted stump, or sapling
which is bent under tension by other wood so that it springs
back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of
springing back to the upright position during the bucking
cut to separate the log from the stump. Watch out for
springpoles—they are dangerous. Do not attempt to cut
bent branches or stumps which are under tension unless
you are professionally trained and competent to do so.

TRANSPORTATION AND STORAGE

Stop the engine, engage the chain brake, disconnect
spark plug wire from the spark plug and allow it to cool
before storing or transporting.
Clean all foreign material from the product.
Drain all fuel from tank into a container approved for
petrol. Remember to properly replace and tighten the
fuel mix cap.
Run the engine until it stops. This will remove all fuel-
lubricant mix that could become stale and leave varnish
and gum in the fuel system.
Drain all bar and chain lubricant from tank into a
container approved for lubricant. Remember to properly
replace and tighten the chain lubricant cap.
Always fit guide bar cover before storing the product, or
during transportation.
Store the product in a cool dry and well-ventilated
place that is inaccessible to children. Keep away from
corrosive agents such as garden chemicals and de-
icing salts. Do not store outdoors.
When carrying the product for short distance (from one
working area to the next), always apply the chain brake
so that the saw chain is restricted from movement.
When transporting the product, secure it against
movement or falling to prevent injury to persons or
damage to the product.
Never carry or transport the product while the engine
is running.
Abide by all government and local regulations for the safe
storage and handling of petrol. Excess fuel should be used
in other 2-cycle engine powered equipment.
MAINTENANCE
Always keep the product in good working condition.
WARNING
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause possible injury, poor performance and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
technician. For servicing and repairs, you have to return
the product to your nearest authorised service centre.
When servicing, use only identical replacement parts.
WARNING
Before inspecting, cleaning, or servicing the product,
stop the engine, engage the chain brake, disconnect
the spark plug wire from the spark plug. Failure to follow
these instructions can result in serious personal injury or
property damage.
You may only make adjustments or repairs described
in this manual. For other repairs, contact the authorised
service centre.
Consequences of improper maintenance may cause
the chain brake and other safety features to not function
correctly, thus increasing the potential for serious injury.
Keep the product professionally maintained and safe.
Sharpening the chain safely is a skilled task. Therefore
the manufacturer strongly recommends that a worn
or dull chain is replaced with a new one, available
from your authorised service centre. The part number
is available in the product specification table in this
manual.
Follow instructions for lubricating and chain tension
checking and adjustment.
After each use, clean the product with a soft dry cloth.
Check all nuts, bolts and screws at frequent intervals
for security to ensure the product is in safe working
condition. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
REPLACING GUIDE BAR AND SAW CHAIN
See page 282 - 285.
1. Stop the product. Wear protective gloves.
2. Disengage the chain brake.
3. Unscrew the guide bar locking knob and remove the
sprocket cover.
4. Remove the bar and saw chain from the product.
5. Clean the underside of the sprocket.
6. To replace the bar with a new one, loosen the screw of
the chain tension assembly. Mount the chain tension
assembly on to the new bar and tighten the screw.
7. Attach the guide bar and chain tension assembly to the
chain saw. Lower the guide bar so that the bolt goes
through the hole in the bar and chain tension assembly.
8. The saw chain should face in the direction of chain
rotation. If they face backwards, turn the loop over.
9. Place the loop around the drive sprocket. Then place
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
English | 7