Positioning; Start-Up; Mains Connection; Working With The Log Splitter - ATIKA ASP 5-UG Notice Originale

Consignes de sécurité , pièces de rechange
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 20
12
A second person must hold the log splitter in vertical
position. Remove the hexagon screws of the support
foot (9). Remove the support foot (9).
13
Together with the second person lift the log splitter
and put it onto the stand.
14
Make also sure that the log splitter safely rests on the
front support leg (A) and rear rod (D).
15
Put the hexagon screws (M8x100) through the hole in
the front support leg (A) and the log splitter. Tighten
the hexagon screw (M8x100).
16
Firmly tighten all screws.
Now, the log splitter is completely assembled on
P
o
s
P
o
If you use the log splitter without frame, position the log splitter
on a work surface at a height of about 60 – 75 cm, this will
create an comfortable working position.
Place chocks under the wheels to prevent the machine rolling
during operation.
Ensure that the working area meets the following conditions:
− no danger of slipping
− level
− free of obstacles
− sufficiently well lit
Do not operate the machine in the direct vicinity of gas or
petrol pipes or containers, or any other easily inflammable
materials.
S
S
Check that the machine is completely and correctly
assembled.
Before using the shredder, make sure each time that
there are no faulty connections (tears, cuts, etc.)
there are no damage at the machine
all screws are tight
check the hydraulic system for any possible leaks

Mains connection

Compare the voltage given on the machine model plate
e.g. 230 V with the mains voltage and connect the
machine to the relevant and properly earthed plug.
Only use connection cables with sufficient diameters.
Connect the machine via a 30 mA fault current safety
switch.
Fuse protection: 16 A
Operating pushbutton
i
t
i
o
n
i
n
g
s
i
t
i
o
n
i
n
g
t
a
r
t
-
u
p
t
a
r
t
-
u
p
Fig. 1
Switching on
Push the green button. The motor is running as long as the
green button remains pushed.
Switching off
Stop pushing the green button.
Do not use any device where the operating pushbutton
does not work properly. Repair or replace damaged
pushbuttons immediately.
Hydraulics
Never operate the machine in the event of any possible
danger from hydraulic fluid.
Ensure that the machine and working area are clean and
free of oil.
Danger of slippage or fire!
Check the hydraulic reservoir regularly to ensure that it
contains enough hydraulic oil (look at "Care and
maintenance")
Capacity:
W
o
r
k
i
n
g
W
o
r
k
i
n
g
SAFETY INSTRUCTIONS
additional
The log splitter may only be operated by a single person.
The machine may only be operated by persons over the
age of 18 years, and who have read and understood these
operating instructions.
Wear protective equipment (safety mask, gloves, safety
shoes) to protect yourself from possible injury.
Never try to split logs containing nails, wire or other similar
objects.
Already split wood and wood chips create a dangerous
working area. The operator may stumble, slip or fall.
Always keep the working area neat and tidy.
Never place the hands on or near any moving parts of the
machine when it is switched on. Maintain a safe distance
from the log, the ram and the wedge in order to protect
your hands from injury.
Split only timber which corresponds to the maximal length
to be worked with.
14
Operating
pushbutton
3.2 litres
w
i
t
h
t
h
e
l
o
g
s
p
l
i
w
i
t
h
t
h
e
l
o
g
s
p
l
i
t
t
e
r
t
t
e
r

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

301760

Table des Matières