Before Starting The Equipment; Fuel And Oil - EINHELL Bavaria BBC 25 Mode D'emploi D'origine

6. Before starting the equipment

Check the equipment for the following each time
before use:
•
That there are no leaks in the fuel system.
•
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.

6.1 Fuel and oil

Recommended fuels
Use only a mixture of unleaded petrol and special
2-stroke engine oil. Mix the fuel mixture as indica-
ted on the fuel mixing table.
Important: Do not use a fuel mixture which has
been stored for longer than 90 days.
Important: Never use 2-stroke oil with a recom-
mended mixing ratio of 100:1. The manufacturer's
warranty will be voided in case of engine damage
due to inadequate lubrication.
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke
oil into the mixing bottle (see scale printed on the
bottle). Then shake the bottle well.
6.2 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol
1 liter
5 liters
7. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from town to
town.
Before starting up the equipment remove the pro-
tective caps from the cutting blade (18).
7.1 Starting the engine when cold
Fill the tank with the required amount of oil/petrol
mix. See „Fuel and oil".
1. Set the equipment down on a hard, level sur-
face.
2. Press the fuel pump (primer) (Fig. 1/Item 7)
ten times
3. Set the On/Off switch (Fig. 1/Item 9) to „I".
4. Secure the throttle lever. To do this, press the
throttle lever lock (Fig. 1/Item 12) and then
Anl_BBC_25_SPK7.indb 21 Anl_BBC_25_SPK7.indb 21
GB
2-stroke oil
25 ml
125 ml
- 21 -
press the throttle lever (Fig. 1/Item 11) and
lock the throttle lever by pressing the lock
(Fig. 1/Item 10) at the same time.
5. Set the choke lever (Fig. 1/Item 5) to „ „.
6. Hold the equipment fi rmly and pull out the
starter cable (Fig. 1/Item 4) until you feel it
begin to resist. Then tug sharply on the starter
cable 4 times. The equipment should start.
Note: Never allow the starter line to snap
back. This may result in damage.
Warning: Since the throttle lever is secured,
the cutting tool will start to operate when the
engine is started.
7. Once the engine has started, move the choke
lever immediately to „ „ and allow the equip-
ment to warm up for approx. 10 seconds.
Then release the throttle lever by simply actu-
ating it (the engine then returns to running in
idle mode).
8. If the engine does not start up, repeat steps
4-8 above.
Please note: If the engine does not start up even
after several attempts, read the section "Engine
Troubleshooting". Please note: Always pull the
starter cord out in a straight line. If it is pulled out
at an angle, then friction will occur on the eyelet.
As a result of this friction, the cable will become
frayed and will wear away faster. Always hold the
starter handle when the cable retracts. Never
allow the cable to snap back when it has been
pulled out.
7.2 Starting the engine when warm
(The equipment has been idle for less than 15-20
min.)
1. Set the equipment down on a hard, level sur-
face.
2. Switch the On/Off switch to „I".
3. Secure the throttle lever (in the same way
as described in "Starting the engine when
cold"). Hold the equipment fi rmly and pull out
the starter cable until you feel it start to resist.
Then tug sharply on the starter cable. The
equipment should start after 1-2 tugs. If the
equipment does not start after 6 pulls, repeat
steps 1 to 8 of the procedure for starting the
engine when cold.
05.11.14 08:28 05.11.14 08:28