Accessories - Milwaukee 4004 Manuel De L'utilisateur

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go on-line to www.milwaukeetool.com. To obtain a
catalog, contact your local distributor or a service center.
Meter Boxes
Cat. No. 48-51-0100 (30 amp, 120 volt)
(Not available in Canada)
Same as supplied with Vac-U-Rig
Cat. No. 4136. Ammeter and power switch appear on the front panel and a
single 20 amp twist lock receptacle for the drill motor and two convenience
outlets are on the back of the box.
Meter Boxes
Cat. No. 48-51-0120 (20 amp, 120 volt)
(Can be used in Canada)
Ammeter and power switch appear on the front panel with a single 20 amp
twist lock receptacle for the drill motor on the back.
Telescoping Extension Assembly
Cat. No. 49-95-1000
This assembly braces the rig between the fl oor and ceiling for maximum
rigidity. It adjusts for 14-foot ceilings and features fi xed hole adjustments.
Copper Washer
Cat. No. 45-88-8565
Before using the tool, slip this washer onto the spindle to prevent the bit
from seizing on spindle during coring.
Spacer Assembly
Cat. No. 49-67-0110
For use with Cat. Nos. 4125 and 4130. Mounts between cradle and Dymodrill
motor when using 10" - 14" coring bits.
Spacer Assembly
Cat. No. 49-67-0115
For use with Cat. No. 4115 and 4120. Mounts between cradle and Dymodrill
motor when using 10" - 14" coring bits.
Water Collecting Ring
Cat. No. 48-70-0060
For use where water fl ow from coring must be trapped and drained. Dike-type
collector ring holds water for fast disposal when used with bits up to 10" in
diameter. A built-in vacuum hose fi tting also allows the ring to be used with
a wet/dry vacuum cleaner.
Water Hose
Cat. No. 49-18-0055
This 8-foot water hose features a 5/8" coupling and standard brass male
and female water hose fi ttings.
Water Tank
Cat. No. 49-76-0055
This 3-1/2 gallon heavy-duty, impact-resistant poly tank is for use where a
regular tap water supply is not available.
Vacuum Pad Assembly (Single Pad)
Cat. No. 49-22-7100
This single vacuum pad is the same as supplied with Vac-U-Rig
Kit No. 49-22-7075. Can be used with Cat. Nos. 4115, 4125 and 4130.
Vacuum Pump Assembly (115 Volts)
Cat. No. 49-50-0160
This heavy-duty 1/8 H.P. pump comes complete with vacuum gauge, air
fi lter and cord. May be mounted to the base of the unit. Same as furnished
®
with Vac-U-Rig 49-22-7075. Can be used with Cat. Nos. 4115, 4125 and
4130.
Vacuum Pump Assembly (115 Volts)
Cat. No. 49-50-0165
page 14
To reduce the risk of injury, always unplug the tool before attaching or
removing accessories. Use only specifi cally recommended accessories.
Others may be hazardous.
® Attachment Kit No. 49-22-7075 and with
®
Attachment

ACCESSORIES

WARNING!
This heavy-duty 1/8 H.P. pump comes complete with vacuum gauge, air
fi lter and cord. May be mounted to the base of the unit. Can be used with
Cat. No. 4120.
Vac-U-Rig® Attachment Kit (115 Volts)
Cat. No. 49-22-7065
This kit includes: (1) vacuum pad; (1) vacuum pump assembly with gauge,
fi lter, 8-foot air hose, and fi ttings. Can be used with Cat. No. 4120.
Vac-U-Rig® Attachment Kit
Cat. No. 49-22-7075
This kit includes: (1) vacuum pad; (1) vacuum pump assembly with gauge,
fi lter, 8-foot air hose, and fi ttings. Can be used with Cat. Nos. 4115, 4125
& 4130.
Threaded Adapter
Cat. No. 48-04-0160
Thread Adapter reduces the thread size of 1-1/4"-7 to 5/8"-11
MILWAUKEE Dymobits and extensions.
Shear Pin No. 44-60-0065 (Low Strength Shear Pin)
Shear Pin No. 44-60-0032* (High Strength Shear Pin)
* (Standard equipment on Dymodrills except clutch Cat. Nos. 4004, 4005,
4092, 4206 and 4097).
9" Bit Extension
Cat. No. 48-95-1500
Extension threaded on both ends with a 1-1/4"-7 thread. For use with Dia-
mond Core Bits over 2" in diameter and a 1-1/4"-7 thread. Extension mounts
directly to the Dymodrill. Two or more extensions can be used together to
core deep holes.
10-1/2" Bit Extension
Cat. No. 48-95-2100
Extension threaded on both ends with a 5/8"-11 thread. For use with 1-1/4"
and 1-1/2" diameter Diamond Core Bits with a 5/8"-11 thread. Extension
requires Threaded Adapter No. 48-04-0160 for mounting to Dymodrills. Two
or more extensions can be used together to core deep holes.
3/16" Socket Wrench
Cat. No. 49-96-0085
Use to mount Dymodrills onto the cradle on Dymorigs
1-3/8" Open End Wrench
Cat. No. 49-96-4700
Use to install bits onto Dymodrills.
Vacuum Pad Gasket
Cat. No. 43-44-0570
Replacement part for vacuum pads on Cat. Nos. 4115, 4125 & 4130
Vacuum Base Gasket
Cat. No. 43-44-0605
Replacement part for vacuum base Cat. No. 4120.
Rubber Cement
Cat. No. 44-22-0060
Use to bond vacuum pad gaskets to vacuum pads on Cat. Nos. 4115, 4120,
4125 and 4130.
Type "E" Grease
Cat. No. 49-08-4122
Use for lubricating rack and pinion as well as spindle.