Software Instructions - BIANCHI VENDING HL/5010 Série Manuel D'emploi Et D'entretien

ENGLISH
– with a cloth soaked with the solution clean the whipper assembly base
(Fig.4.10)
– the parts must soak in the solution for the time indicated on the solutions'
instruction label.
– Recover all the parts, rinse them abundantly, dry them perfectly and
proceed with the re-assembly in the distributor.
After re-positioning the container undertake to raise the flap in order to reset
the correct function (fig. 4.11).
For further safety after the assembly of the parts, effect some auto-
matic cleaning cycles so as to eliminate any eventual residues.
4.5 Product container loading
4.5.1 Loading containers
Filling is possible keeping the containers inserted, and by raising the upper
flap of the distributor (Fig. 4.12) or by extracting each container.
For granulated coffee in particular it is necessary to close the closure plat
before extracting the container.(Fig.4.13).
– remove the covers of each container and load the product according to
the product indicated on the label (Fig.4.14).
– pay attention that they there are no clots, avoid pressing the product
and using an excessive quantity, so as to avoid its aging in relation to the
consumption forseen in the time period between two loadings.
Check the container product capacity in the section TECHNICAL CHARACTE-
RISTICS.
4.5.2 Payment system installation
The distributor does not have a payment system; any possible damages to
the distributor itself and/or objects and/or people deriving from its incorrect
installation are responsibility of who installs the payment system.
In-series arrangement for connection of the validator unit, 12-24 V.
For Executive/MdB kit payment systems.
The switches are to be directly connected to the keyboard card, the executive
serial systems require the payment system kit supplied separately.
Then go into programming for the correct settings.
Consult chapter "5.0 SOFTWARE INSTRUCTIONS" so as to verify setting of
the parameters, that must be coherent with the system used.
4.5.3 Cup loading
Use only cups designed for automatic vending machines, with a diameter
of more than 70-74 mm, avoid compressing the cups between themselves
during the loading.
Loading must be carried out with machine off.
In installation phase with the cup dispenser completely empty, operate as
follows:
- Lift the bracket (Fig.4.15)
- Lift the cup column cover (Fig.4.16)
- Load the cups in the four tubes of the cup column (Fig.4.17)
- replace the cover and lower the bracket (Fig.4.18)
4.5.4 Stirrer filling
Use only stirrers specifically designed for automatic dispenser ma-
chines.
- remove the metal weight from the column device (Fig. 4.19)
- Insert spoons, with their packaging band, into the upper section of the
column and place them on the bottom, then cut and remove the band
(Fig.4.20).
– Check that the spoon are cut burr-free, that they are not bent and that
they are all placed horizontally.
- complete filling and replace the small weight (Fig. 4.21)
(with machine off)

5.0 SOFTWARE INSTRUCTIONS

STANDARD MODE
PUSHBUTTON PANEL
The pushbuttons provided are meant for:
Key 1: Selection 1
Key 2: Selection 2
Key 3: Selection 3
Key 4: Selection 4
Key 5: Selection 5
Key 6: Selection 6
Key 7: Selection 7
Key 8: Selection 8
Key 9: Selection 9
Key 10: Selection 10
Key 11: Selection 11
Key 12: Selection 12
All the keys can also be used for the pre-selection functions.
On the SF0519A circuit board:
Key P: Programming
Key M: Maintenance
Please consult the description hereunder concerning the use of the DP1 and
DP2 pre-selection functions.
By programming either the DP1 or DP2 pre-selection function on one of the
P1 or P2 keys, then pressing on either the DP1 or DP2 pre-selection keys
followed by a second key, will activate selection options numbered 13 to 24
according to the following table:
Key number LEI 200
DP1 + Key 1
DP1 + Key 2
DP1 + Key 3 Selection 13
DP1 + Key 4 Selection 14
DP1 + Key 5 Selection 15
DP1 + Key 6 Selection 16
DP1 + Key 7 Selection 17
DP1 + Key 8 Selection 18
DP1 + Key 9
DP1 + Key 10
DP1 + Key 11
DP1 + Key 12
DP2 + Key 1
DP2 + Key 2
DP2 + Key 3 Selection 19
DP2 + Key 4 Selection 20
DP2 + Key 5 Selection 21
DP2 + Key 6 Selection 22
DP2 + Key 7 Selection 23
DP2 + Key 8 Selection 24
DP2 + Key 9
DP2 + Key 10
DP2 + Key 11
DP2 + Key 12
Nota: sui tasti programmati come preselezioni non saranno ovviamente
disponibili le relative selezioni.
In the programming mode the keys have the following meaning:
Key 1: Increase value
Key 2: Escape
Key 3: Decrease value
Key 5: Move cursor
key 7: Enter
16