Getting Started With The Generating Set - Kohler SDMO INVERTER PRO 3000 E Manuel D'utilisation Et D'entretien

2.7.4 Connection and choice of cables
For all connections, use flexible, strong rubber-sheathed cables which comply with standard IEC 60245-4 or equivalent cables, and
ensure that these are kept in perfect condition. Only use one item of class I electrical equipment per socket and connect up
equipment using a cable equipped with a PE protective conductor (green/yellow); this protective conductor is not required for
class II equipment. Adhere to the cross sections and lengths recommended in this table during installation or when using electrical
extensions.
Equipment type:
Type of unit connector:
Recommended cable cross section:
0 to 50 m
Length of
51 to 100 m
cable used
101 to 150 m*
*This cable length is the maximum permitted length, and must not be exceeded.
Installation method = cables on raceway or non-drilled tablet/Permitted drop in voltage = 5%/Multi-core conductors/Cable type PVC 70°C (e.g.
H07RNF)/Ambient temperature =30°C.
2.8 Risk of hearing loss
RISK OF HEARING LOSS
Suitable hearing protection must be worn at all times when the unit is running.
DANGER
2.9 Risks during handling operations, use and maintenance
For safety reasons, all operations must be carried out by staff with the necessary skills and using suitable
equipment. Maintenance must be carried out on a regular and conscientious basis, using only original parts. Gloves
must be worn.
Precautions to be observed when handling petroleum-based products:
RISK OF POISONING OR EXPLOSION
Respect the local regulations in force concerning the handling of petroleum products. Fill up
when the unit is switched off and the engine cold. When filling the tank, smoking, using a
naked flame, producing sparks and making telephone calls are forbidden. After filling, always
check that the tank's filler cap is properly tightened. Clean any traces of fuel with a clean cloth
and wait until the vapours have dispersed before starting the unit.
The fluids used by the units, such as oils and fuels, are dangerous products. Never ingest
DANGER
them. Avoid prolonged or repeated contact with the skin.
Precautions to be observed when handling batteries:
RISK OF POISONING OR EXPLOSION
Follow the battery manufacturer's recommendations. Only use insulated tools. Keep away
from fire or naked flames. Always ensure adequate ventilation during charging.
DANGER

3 Getting started with the generating set

3.1 Key to illustrations
The cover illustrations can be used to identify the various components of the unit. The procedures in the manual refer to these
illustrations using letters and numbers as identifiers: "A1" refers to the number 1 on figure A.
Earth terminal
Nuts
Enclosure
Battery housing nuts
Battery retaining strap
Battery
Switch
Wheel locking lever
Inspection flap screw
Inspection flap
Oil filler cap
Fuel level indicator
Fuel tank cap
Screen filter
Economic idle speed (Hare-
Tortoise)
* Source inverter, battery charger, etc.
10 A
mm² AWG
4 10
10 7
10 7
A1 Fuel tap
A4 Choke
A3 Operating light
A4 Starter-recoil reel handle
Electric
A5
(alternating current)
12 V socket
A6
current)
Circuit breaker for 12V
A7
socket
A8 Oil drain screw
A9-E1 Spark plug
A10-E2 Air filter
A11-B1 Oil cut-out warning light
A12 Overload warning light
A13 Correct oil level
A14-C1 Oil drain cap
A15 Oil drain plug
Single-phase
16 A 32 A
mm² AWG mm²
6 9 10
10 7 25
16 5 35
A16
A17
A18
A19
sockets
A20
(direct
A21
A22
A23
A24-E4
A25-D2
A26
A27
B2
B3
B4
17/182
Three-phase
10 A
AWG mm² AWG
7 1.5 14
3 2.5 12
2 4 10
Oil drain screw seal
Fuel drain pipe
Fuel drain screw
Air filter cover fasteners
Air filter cover
Foam element
Paper element
Spark plug access cover
screws
Spark plug cap
Exhaust silencer cover screw
Exhaust silencer cover
Exhaust silencer grille screw
Exhaust silencer
Exhaust silencer grille
Spark arrester
16 A
mm² AWG
2.5 12
4 10
6 9
B5
C2
C3
D1
A2
D3
D4
E1
E3
F1
F2
F3
F4
F5
F6