Ec Declaration Of Conformity - Kohler SDMO INVERTER PRO 3000 E Manuel D'utilisation Et D'entretien

8.5 Recommended fuel quality
Using fuel which does not comply with the following specifications exposes the equipment to irreversible damage not covered under
warranty:
- Cleanliness and quality: ensure that the petrol used does not contain water and that it is fresh and clean (not out of date or
contaminated). For the
- Octane rating: minimum octane rating of 87 (R+M)/2 or minimum octane rating of 90 (RON = Research Octane Number)
- Blends: the use of unleaded petrol containing up to 10% ethyl alcohol is authorised (France: SP95-E10). It is not permitted
to use unleaded petrol containing less than 90% petrol, e.g. E15, E20 or E85. Blends of methyl tert-butyl ether (MTBE) and
unleaded petrol are approved (up to a maximum of 15% MTBE by volume).
However, it is strongly recommended that the same type of fuel is used throughout the complete service life of the unit. If the unit is
used infrequently (less than once a month), use new fuel with each use or add a stabilizing additive to the fuel tank.
8.6

EC Declaration of conformity

We, SDMO Industries - 270 rue de Kerervern, 29490 GUIPAVAS/CS 40047, 29801 BREST CEDEX 9 – France, hereby declare
under our sole responsibility that the following electrical generating sets:
Equipment
description:
Generating set KOHLER-SDMO
1. Comply with the safety requirements set out in the Low Voltage Directive - 2014/35/EU of 26 February 2014 in application of the
harmonized standard EN 60204-1: 2006 (AMD 1 2006, COR 2010)
2. Comply with the provisions of the following Directives:
- Machinery - 2006/42/EC of 17th May 2006 in application of the harmonized standard ISO 8528-13
- Electromagnetic compatibility - 2014/30/EU of 26th February 2014 in application of the harmonized standards EN 60034-1:
2010 (COR 2010) / EN 61000-6-1: 2007 / EN 61000-6-2: 2005 (COR 2005) / EN 61000-6-3: 2007 (AMD1 2011,
AMD1/COR 12) / EN 55011: 2009 (AMD 1 2010)
- Relating to the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2) -
2011/65/EU of 8th June 2011 (from 23rd July 2019) in application of the harmonized standard EN 50581: 2013
- Relating to noise emission in the environment by equipment for use outdoors - 2000/14/EC of 8th May 2000, via the
compliance procedure set out in Annex VI:
Notified body:
ABOMA B.V.
Galvanistraat, 1 -
Postbus 141 -6710 BC
EDE - Netherlands
Name and address of the person authorized to create and hold the technical file:
H. PRIGENT, 270 rue de Kerervern, 29490 GUIPAVAS / CS 40047, 29801 BREST CEDEX 9 – France.
Make: Trade name:
INVERTER PRO 3000 E
Trade name: Type:
INVERTER
3499231003091
PRO 3000 E
Type:
3499231003091
Measured sound
power level:
87 dB(A)
25/182
Serial numbers:
7CG 0380101 > 7CG 0380999
7CG 4300101 > 7CG 4319999
7PB-5000101 > 7PB-5039999
7PB-5040101 > 7PB-5079999
7CH 2570101 > 7CH 2570999
7CH 2572101 > 7CH 2572999
7CH 2580101 > 7CH 2587999
7CH 2590101 > 7CH 2591999
Guaranteed sound
Rated output:
power level (LwA):
88 dB(A)
GUIPAVAS, 10/2018
H. PRIGENT
President, SDMO Industries
2800W