Publicité
Les langues disponibles
Les langues disponibles
Maintenance and cleaning
Always disconnect the appliance from the
mains before cleaning. Allow the entire unit to
cool to room temperature before proceeding.
•
After each use, remove the silicone sealing
ring and blocking device from the bottom
of the high-pressure lid, wash with a mild
detergent and dry. The blocking protection
can be removed by pushing the side of
the blocking protection in one direction
and pulling it off the hooks. The blocking
protection can now be removed.
•
Wash the inner pot with a mild detergent
after you have removed them and they have
cooled down. Rinse with water and then
gently pat dry with a tea towel.
60
•
The inner pot can be washed in the dish-
washer, but this may reduce their lifespan.
•
Wipe the entire interior and exterior dry with
a tea towel after each use to prevent rusting.
•
To clean the outside of the Smart Pressure
Cooker, use only a slightly damp cloth.
•
After cleaning all parts, make sure that the
silicone sealing ring and the locking device
are placed back in the right place at the
bottom of the lid and fit tightly.
•
Do not use scouring pads, powders or
chemical cleaning agents to clean (parts of)
the Smart Pressure Cooker.
•
Check regularly that the steam valve and
the pressure relief valve are clean and
undamaged.
Troubleshooting
Problem
Possible cause
The high-pressure cover
1. The silicon sealing ring is not
does not close properly.
properly attached.
2. The cover is not properly seated
on the housing.
I experience problems
1. There is still pressure in the inner
opening the high-pressure
pot.
cover.
2. The pressure relief valve is stuck
in its outermost position
.
Steam leaks out of the side
1. The silicone sealing ring is missing.
of the high-pressure cover.
2. The silicone sealing ring is defec-
tive/broken.
3. Food residues on the silicone
sealing ring.
4. The lid is not firmly in place.
Steam leaks from the pres-
1. There is food stuck on the silicone
sure relief valve for more
seal on the underside of the
than 2 minutes.
pressure relief valve.
2. The silicone seal of the pressure
relief valve is worn.
The pressure relief valve
1. There is not enough water in the
does not rise.
inner pot.
2. The sealing ring of the pressure
relief valve can be broken.
Steam continues to come
1. The steam valve is not attached or
out of the steam valve.
not attached properly.
2. The high-pressure system does
not work any more.
Rice is not fully cooked/
1. Not enough water has been
too firm.
added.
2. The high-pressure cover has
been opened too early.
Solution
1. Replace the silicone sealing
ring and make sure it seals well
everywhere.
2. Lift the housing cover, place
it back on the housing, turn
clockwise and make sure the
arrows on the housing and lid
are aligned with the closed-lock
symbol.
1. Press Release Pressure button to
release pressure.
2. First follow step 1 to make sure
that all pressure has been re-
leased. Now gently press on the
pressure relief valve with a long
tool or pen.
1. Place the silicone sealing ring.
2. Replace the silicone sealing ring.
3. Clean the silicone seal ring.
4. Open the lid and close it again.
1. Wipe the silicone seal on the
underside of the pressure relief
valve clean
2. Replace the silicone seal on the
pressure relief valve.
1. Add more water to the inner pot,
according to the recipe.
2. Replace the sealing ring of the
pressure relief valve.
1. Place the steam valve on the
iron steam outlet on top of the
high-pressure cover.
2. Contact your point of purchase.
1. Adjust the ratio of rice to water
according to the recipe.
2. Once the cooking program is
completed, leave the pressure lid
closed for another 5 minutes.
61
Publicité
