Anti-Chipping Wheels; Cleaning; Cleaning The Machine - Stiga MPST 84 Li 48 V1 Manuel D'utilisation

Masquer les pouces Voir aussi pour MPST 84 Li 48 V1:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

NOTE
During recharging, all machine 
functions are disabled, even if the key 
is turned to the drive position.
WARNING
The battery fitted on the machine has been 
designed and manufactured for this type of use, 
therefore:
- do not disconnect or remove the batteries from 
their housings;
- do not replace the batteries with non-original 
ones;
- do not perform any work which is not mentioned 
in this manual.
In the event a problem with the batteries, 
please contact your Dealer.

8.3 ANTI-CHIPPING WHEELS

The different heights of the wheels allow 
you to maintain a safe distance "H" 
between the cutting-means assembly 
and the ground (Fig. 25.A, Fig. 26.A).
Adjust the position of the anti-chipping wheels 
according to how irregular the ground is.
SAFETY INSTRUCTIONS
This should always be performed on 
both wheels, positioning them at the 
same height, with the machine off.
a. For side discharge models:
To change the position:
1. Unscrew and remove the screw (fig.25.B)
2. Reposition the wheel (fig. 25.A) with 
the spacer ( fig. 25.C) inside the 
hole at the desired distance
3. Tighten firmly the screw (fig. 25.B) 
in the nut (fig. 25.D).
b. For models with rear collection
To change the position:
1. Unscrew the nut  (fig. 26.B) and 
extract the pin (fig. 26.C);
2. reposition the wheel (fig. 26.A) 
in the desired position;
3. reassemble the pin (fig. 26.C), making 
sure the pin head (fig. 26.C) is facing 
the inside of the machine;
4. Tighten the nut firmly (fig. 26.B).

8.4 CLEANING

Clean thoroughly following the instructions 
below every time it is used.

8.4.1 Cleaning the machine

• Clean the outside of the machine 
washing the plastic parts of the bodywork 
with a damp sponge using water and 
detergent, being careful not to get the
electric motors, the battery and the 
electrical system components wet.
• To reduce fire hazards, keep the motor 
and the battery compartment free of 
grass, leaves, or excessive grease.
• Lift the bonnet and clean with compressed 
air any dirt or grass accumulating 
on top of the battery pack.
• Keep the push button panel
free of dirt and debris.
WARNING
Never use high-pressure water or aggressive 
liquids to wash the bodywork and electric motors.
8.4.2 Cleaning the discharge chute
(only for rear collection models)
If the discharge chute is clogged:
1. remove the grass catcher or  the 
rear discharge guard;
2. remove the grass cuttings; you can reach 
them from the channel discharge opening.
8.4.3 Cleaning the grass catcher
(only for rear collection models)
1. Empty the grass catcher.
2. Shake it to remove grass 
cuttings and soil residue.
3. Replace the grass catcher and clean
the interior of the cutting-means 
assembly (par. 8.4.4-a) now remove 
the grass catcher, empty and rinse it, 
then place it where it can dry quickly.
8.4.4 Cleaning the cutting-
means assembly
Clean the cutting-means assembly thoroughly 
to remove any grass remains or debris.
CAUTION
Keep people or animals away from 
the surrounding area when cleaning 
the cutting-means assembly .
a. Cleaning the interiors
When washing the inside of the cutting-
means assembly and the discharge chute, 
the machine must be on firm ground with:
EN - 21

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mpst 84 li 48 v2Mps 84 li 48 v1Mps 84 li 48 v2Mpns 84 li 48 v1Mpns 84 li 48 v2Mp 84 li 48 v1 ... Afficher tout

Table des Matières