Bezzera B2013 Manuel D'instructions page 43

The quantity of steam supplied is proportional
to the opening of the tap; the greater is the
opening of the tap, the greater the quantity of
steam supplied will be.
4) Once the output of steam is concluded, remove
the fluid container and clean immediately the
steam nozzle with a wet cloth from the residues
of the heated fluid.
Warning: do not touch the steam nozzle
directly because it is hot.
DE Model whit automatic steam nozzle
The machine is also equipped with automat-
ic steam nozzle with temperature sensor (Fig.
01-01A-01B; pos. 4a); to operate this nozzle press
the button (Fig. 06-13; pos. g). The steam flow
can be stopped before reaching the set tempera-
ture by pressing again the same button. By holding
down the button (Fig. 06-13; pos. g) steam is con-
tinuously supplied until the button is released. To
avoid suction of fluid into the boiler, discharge the
steam by pressing the button (Fig. 06-13; pos. g).
To change the "texture" of air bubbles present in
the fluid to be heated, operate on the adjusting
screw (closed small bubbles – open big bubbles
(Fig. 12) starting from the open condition (large
bubbles) and reducing gradually the air flow until
reaching the "texture" desired..
To change temperature setting, follow the instruc-
tions in paragraph 5.7 of this handbook.
Warning: To make a cappuccino, we recommend
the use of milk at a temperature of 5 ° C.
5.5 Picking up of hot water
1) Position the water container under the nozzle
(Fig. 01-01A-01B; pos 5).
PM Model
2) Press key (Fig. 01-01A-01B; pos. 2) to pick up
the quantity of water needed.
DE Model
2) Press key (Fig. 06-13; pos. e) to pick up the
quantity of water needed.
Warning: do not touch the nozzle direct-
BEZZERA B2013-B2016-C2013 Compact -Woody
MOD.
ly because it is hot.
5.6 Turning off the machine
1) Close the water shut-off valve
2) Bring the switch (Fig. 01-01A-01B; pos 10) in
pos "OFF" (Red light (Fig. 01-01A-01B; pos.
15) turn OFF).
3) Bring the omnipolar switch of the electric net-
work in idle position "0".
4) Exhaust the pressure of the steam tap.
5.7 Programming of doses
To adjust doses in DE machines, proceed as fol-
lows:
press the continuous output /programming/stop
key (Fig. 06-13; post f), keep it pressed until the
relative light starts flashing, notifying (the machine
must not supply water) the beginning of the pro-
gramming function which lasts 4 seconds (DE
Model), 30 seconds (DE Model whit automatic
steam nozzle) if a key to program is not pressed.
Activate the output of any key of the keyboard
(Fig 06-13; pos a-b-c-d, g) to start programming
which will be memorized when the key will be
pressed again to stop output.
Repeat this operation for all keys in order to pro-
gram the wanted doses.
By programming the first group on the left, the set-
tings will be automatically transmitted to the other
groups. To set different programming between one
group and the other, set them individually.
For setting the automatic steam nozzle (Fig.
01-01A-01B; pos. 4a), insert this last into the fluid
to be heated, press the button (Fig. 06-13; pos.
g) and wait until temperature reaches the desired
value; press again the button (Fig. 06-13; pos. g)
to confirm setting.
5.7.1 "PRE-BREWING" programming
The possibility to select the "PRE-BREWING" func-
tion has been foreseen.
Machine off. Turn on the machine by pressing:
- Key "a" (Fig. 06-13) of the first group to EN-
43
Warning: models DE ensure the setting
of the coffee volume by dose. The auto-
matic steam nozzle ensures to reach
the desired temperature.
(DE Model)