Bezzera B2013 Manuel D'instructions page 42

BEZZERA B2013-B2016-C2013 Compact-Woody
MOD.
5 – USE OF MACHINE
5.1 Start up of machine and loading of
water inside boiler
Open the water shut-off valve.
Bring the lever of the omnipolar switch belonging
to the electric system on ON.
When the switch (fig. 01-01A-01B; pos 10) is
brought in position "1" (Red light turn on Fig.
01-01A-01B; pos. 15), the water is loaded in-
side the boiler; after 120 seconds of loading, the
machine goes in alarm status; bring the switch in
"0" position and repeat the operation by pressing
the same switch a few times, until the pump has
completely loaded the boiler and shuts off.
Once the minimum level has been reached, the
green light (Fig. 01-01A-01B; pos 9) will turn on
and the switch (Fig. 01-01A-01B, pos. 10) can
be brought in position "2" to enable the resistor
and you will have the orange light turns on (Fig.
01-01A-01B, pos. 8).
Wait that the boiler's pressure gauge (Fig.
01-01A-01B; pos 11) indicates a pressure be-
tween 1 and 1.2 bar (0.1 – 0.12 MPa) prior to
use the machine.
5.2 Heating
To make sure that the machine has reached the
right thermal balance between temperature and
pressure, when the boiler's gauge indicates a
pressure between 1 and 1.2 bar (0.1 – 0.12
MPa), press the steam tap (Fig. 01-01A-01B; pos
1) and exhaust the steam 2 or 3 times in the dis-
charge basin.
The green light (fig. 01-01A-01B; pos 9), if turn
off, warns about the insufficient water level inside
the boiler.
The orange light (fig. 01-01A-01B; pos 8), if turn
on, signals the enabling of the resistor.
Warning:
when the green light (fig. 01-01A-01B; pos 9) is
off, a safety device does not allow the machine
to work; contact the technical assistance service.
5.3 Preparation of coffee
Warnings:
- Do not remove the filter holder when the device
is on: burning hazard.
- Do not touch directly the metal part of the filter
holder and group: burning hazard.
- The standard doses for the filters are 8 grams
for a dose and 16 grams for two doses.
1) Remove the filter holder from the supply group.
2) Load the filter holder with ground coffee, press
the coffee paying attention not to dirty the bor-
der of the filter holder.
3) Hook back the filter holder in its location.
4) Act on the coffee supply command, by press-
ing one of the keys (Fig. 01-01A-01B; pos. 3),
based on the dose to supply.
Press again the button (Fig. 01-01A-01B; pos. 3)
to stop supply when the desired dose has been
reached.
4) Act on the coffee supply command, by press-
ing one of the keys (Fig. 06-13; pos. a-b-c-d),
based on the dose to supply.
To change the programming of doses, follow the
instructions indicated in paragraph 5.7 of this
booklet.
The machine is also conceived for continuous out-
put:
1) start the output by pressing the continuous out-
put key (Fig. 06-13; pos. f)
2) stop the output once the wanted quantity has
been reached, by pressing once again the con-
tinuous output key (Fig. 06-13; pos. f)
Warning: The machine is equipped with
an automatic safety device that stops
continuous output after the third con-
secutive litre.
5.4 Steam supply
1) To avoid refluxes of fluid inside the boiler, ex-
haust the steam by acting on the tap's knob (fig.
01-01A-01B; pos. 1).
2) Introduce the steam nozzle (Fig. 01-01A-01B;
pos 4) in the fluid container to heat up.
3) Press the steam key (Fig. 01-01A-01B; pos 1).
42
PM Model
DE Model