Flame Height / Standby; Switching Off; Temperature Display; Time - Dru SCENIC SL 70 Instructions D'installation Et Mode D'emploi

Caution - If the pilot burner is not burning after 3 ignition
attempts, you must close the gas tap and call
the installer;
- When igniting the pilot burner, you will hear
sound signals. After the last short sound signal,
the main burner should be largely ignited within
about 10 seconds. If this is not the case, you
must close the gas tap and warn your installer;
- If the appliance ignites with a pop sound, you
must close the gas tap and contact your installer.
!Tip A little motor will start to run when the main
burner operates, you will be able to hear it.

Flame height / standby

The flame height can be adjusted continuously by using the
buttons (small flame) and
to lower the flame height, the appliance can be set to the
standby position; this means that only the pilot burner will
still be burning.
• Press button (small flame) to lower the flame height and/
or to set the appliance in the standby position.
• Press the button (large flame) to raise the flame height
and/or to switch on the main burner from the standby
(pilot burner) position.
Caution - If you continue to press down button
(large flame) on the remote control, the main
burner should be largely ignited within about 10
seconds. If this is not the case, you must close
the gas tap and warn your installer;
- If the appliance ignites with a pop sound,
you must close the gas tap and contact your
installer.

Switching off

Switch the appliance off by pressing the OFF button.
The pilot burner will also go out.

Temperature display

The room temperature can be indicated on the display
in degrees Celsius (ºC) using a 24 hour clock or degrees
Fahrenheit (ºF) using a 12 hour clock.
• Simultaneously press OFF and
correct display appears.

Time

The display can indicate time.
After placing the battery or simultaneously pressing
(large flame) and (small flame), the time indication will
flash on the display and you will be able to adjust the time.
• Simultaneously press and
flashes on the display.
• Press the button (large flame) to set the hours.
• Press the button (small flame) to set the minutes.
• Press OFF to return to the MAN position, or wait for the
system to automatically return to the MAN position.
(large flame). By continuing
(small flame), until the
until the time indication
OPERATING INSTRUCTIONS

Thermostat function

Using the thermostat function you can set two
temperatures, which can be controlled thermostatically.
These temperatures are referred to as day temperature
and night temperature.
✹
The TEMP and TEMP symbols on the display refer to
day and night temperature respectively.
The room temperature is compared to the set day/night
temperature and then the flame height is automatically
controlled in order to reach the set temperature.
To be able to use the day/night temperature function, the
appliance must be in the standby position.
!Caution - Always leave the remote control at the same
place, so that the thermostat is able to 'feel' the
room temperature;
- Make sure this place is free from influences
such as draught, heat from radiators and direct
sunlight.
Example
✹
By using the TEMP function you can keep the day
temperature at 20 ºC; while you use the
at night to maintain a temperature of 15 ºC.

Setting day/night temperature

By using the SET button, you will go through the following
functions:
→ ✹ →
MAN TEMP
• Briefly press the SET button to enter the
TEMP position.
• Press the SET button until the temperature on the display
flashes.
• Set the required temperature by using the buttons
(large flame) and (small flame).
!Caution - The minimum temperature you can set is 5 ºC /
40 ºF;
- Control of the night temperature is switched
off by lowering the temperature until two
stripes ("--") appear on the display.
• Press the OFF button or wait until position
TEMP appears on the display.

Activating the thermostat function

For activating the thermostat function, you must proceed
with the following steps:
• Place the appliance in the standby (pilot burner) position
using button (small flame).
• Set the day/night temperature.
✹
• Choose the TEMP or
button.

Timer for thermostat function

Using the timer enables you to set two times per 24 hours
for switching on the day temperature and two times per 24
hours for switching on the night temperature.
33
TEMP function
→ →
TEMP (P*)TIMER MAN
✹
TEMP or the
✹
TEMP or
TEMP function using the SET
Scenic SL