Stenciling; Operating The Front Caster; Cleanup; Special Cleanup Instructions For Use With Flammable Solvents - Titan PowrLiner 850 Mode D'emploi

Operation
4.8

Stenciling

To stencil with this line striper, make multiple spraying
passes from right to left over the stencil with the spray gun
connected to the gun holder. Or, the spray gun can be
removed and used independently from the striper.
To remove the spray gun:
1. Perform the Pressure Relief Procedure in the Operation
section of this manual.
2. Loosen the gun holder block knob on top of the gun
holder.
3. Slide the spray gun out of the gun holder.
4.9

Operating the Front Caster

The front caster on the cart is designed to track the sprayer in
either a straight line or allow free-wheel striping. To adjust the
front caster:
1. Pull the handle on the side of the caster up and back to
release the wheel for free-wheel striping.
2. To lock the wheel back into place, pull the handle down.
Once the front wheel is turned straight again, the wheel
will lock back into place.
5.

Cleanup

The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so
permits material to build up, seriously affecting
Attention
the performance of the unit.
Always spray at minimum pressure with the
gun nozzle tip removed when using mineral
spirits or any other solvent to clean the sprayer,
hose, or gun. Static electricity buildup may
result in a fire or explosion in the presence of
flammable vapors.
5.1 Special cleanup instructions for use with
flammable solvents
• Always flush spray gun preferably outside and at least
one hose length from spray pump.
• If collecting flushed solvents in a one gallon metal
container, place it into an empty five gallon container,
then flush solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
PowrLiner 850
GB
5.2

Cleaning the sprayer

1. Follow the "Pressure Relief Procedure" found in the
Operation section of this manual, section 4.5.
2. Remove the gun tip and tip guard and clean with a
brush using the appropriate solvent.
3. Place the siphon tube into a container of the
appropriate solvent (refer to recommendations of the
material manufacturer). An example of the appropriate
solvent is water for latex paint.
4. Place the return hose into a metal waste container.
5. Turn the relief valve knob to the PRIME (
6. Start the engine.
7. Slowly turn the DirectLink pressure control knob
counterclockwise to increase the pressure until fluid
starts to come out of the return hose. Use only enough
pressure to keep the fluid coming out.
8. Allow the fluid to circulate through the sprayer and
flush the paint out of the return hose into the metal
waste container.
9. Turn off the sprayer by pressing and holding the engine
shutoff switch until the motor shuts off.
10. Place a metal waste container underneath the spray
gun to catch the paint and solvent.
11. Start the engine.
12. Turn the relief valve knob to the SPRAY (
13. Turn the DirectLink pressure control knob slowly
counterclockwise to increase the pressure.
14. Fully pull the spray lever on the cart handle to trigger
the spray gun. Fluid will begin flowing through the
spray hose and out of the gun.
15. Continue to pull the spray lever on the cart handle until
the material is flushed out of the hose and the solvent
coming out of the gun is clean.
16. Release the spray lever.
i
For long-term or cold weather storage, pump
Pump Saver™ through the entire system.
17. Follow the "Pressure Relief Procedure" found in the
Operation section of this manual.
18. Store the sprayer in a clean, dry area.
Do not store the unit under pressure.
Attention
Do not put the high-pressure hose into
solvents. Use only a wet cloth to wipe down the
outside of the hose.
Attention
15
Cleanup
k
) position.
p
) position.