Publicité
Les langues disponibles
Les langues disponibles
Power Up Settings
Power Up Mode: Configures the power up mode
preference. Always On, Standby, and Last State
options are available.
Power Mode: If this feature is enabled the Display
can be turned on again with the RS232 and LAN
commands if it is turned off through it. Press OK to
enable or disable the feature.
Enabled - Reactive mode
Disabled - Eco mode
HDMI Wake Up Enabled: This feature works based
on HDMI 5V signal and it will only work with a
single HDMI source. When this signal is active the
Display wakes up and when the signal is inactive the
Display shuts down. You can enable or disable this
option by pressing OK. In order to use this feature
in conjunction with the Auto Source Switch feature it
is recommended to enable the Auto Source Switch
option in the Options > Controls menu.
Note: This feature may not be available depending on the
model of your Display.
USB
Clone to USB: Copies the database files from the
Display to a connected USB device.
Clone from USB: Copies the database files from a
connected USB device to the Display.
USB Operations: Highlight and press OK to perform
USB operations.
USB Information: Press OK to open the USB
Information menu screen. Current total and free
space information of the connected USB device will
be displayed. You can also format the connected USB
device as device storage using the Format Disk option
in this menu (FAT32 format only) to extend the storage
capacity of your Display. After doing this, that device
will only be usable with the Display.
IMPORTANT: Formatting your USB storage device
will erase ALL the data on it and its file system will be
converted to FAT32.
USB Option: Set to Off to disable the USB ports on the
Display. You can also set this option to 5V to provide
5 volts power over USB. In this case it will still not be
available to browse the USB content via the Media
Player feature of the Display.
Safely Remove: You can use this option to remove
the devices connected to the USB inputs of the Display
safely. Highlight this option and press OK. Wait for
the message to be displayed on the screen and then
remove your device. Failure to do so, may cause
problems when you connect your USB device to other
devices and you might have to format your USB device.
OPS Settings
Press OK to open the OPS Settings menu screen.
This menu cannot be displayed if the OPS module
is not plugged in .
OPS Status: Displays whether the OPS module is
on or off. Allows the change of status via soft PSON
signal (0.5s).
OPS Power: Highlight and press OK to turn the OPS
module on or off.
Power Down: Turns the OPS off via hard PSON
signal (5s).
Boot Signal: Enables or disables sending of a PSON
signal. The Display checks the status signal of the OPS
at bootup in order to turn it on by sending a PSON
signal if it is off. Some OPS's send incorrect information
on their status during the bootup of the Display, so
they seem to be on even though they are off. For such
non-standard OPS's, this option must be enabled. In
this case, a PSON signal will be send for the OPS
regardless of the received status information at bootup.
Recovery Mode: When this option is enabled and
OPS is on, if there is no video for 10 seconds it resets
hotplug. If there is no video available after 30 seconds
it reboots OPS.
OPS Always On: When this option is enabled, the
Power Mode option in the Display Settings > Options
> Power Up Settings menu will be forced to enabled
(Reactive mode) and greyed out in the menu and OPS
will not be set to standby.
SDM Version: Displays the SDM version information.
Volume Settings
Volume Limit: Sets the maximum value of the volume.
Volume Limit (Headphone): Sets the maximum value
of the headphone volume.
Startup Volume Enable: Enables or disables the use
of startup volume value which is set in the Startup
Volume Value menu item. If this option is disabled,
this menu item will be unavailable to be set. Press
OK to enable or disable the feature.
Startup Volume Value: Sets the startup value of the
volume.
Fixed Volume Enable: Enables or disables the use of
fixed volume value which is set in the Fixed Volume
Value menu item. If this option is disabled, this menu
item will be unavailable to be set. Press OK to enable
or disable the feature.
Fixed Volume Value: Sets the value of the volume
to be fixed.
Headphone Direct Volume: When this feature is
enabled, the sound is routed directly to the headphone
English - 21 -
Publicité
