Publicité
Les langues disponibles
Les langues disponibles
enabled, the picture and OSD (On-Screen Display)
will be shifted at specified time intervals.
No Signal: Sets the behavior preference of the
Display, when no signal is detected from the currently
set input source. Failover and Input Search options
are available.
If Failover is selected the Display checks the
connected USB device for available files to play. If no
playable files are available or there is no USB device
connected to the Display, the No Signal Image will be
displayed. If there isn't any No Signal Image available,
No Signal OSD will be displayed on the screen. The
setting of the USB Auto Play option in the Display
Settings > System Settings > More menu is not
important, in Failover mode it will function anyway.
If Input Search is selected, available input sources
will be listed. Highlight the options you want and press
OK to select. The Display will search all selected input
sources consecutively to find signal. If no signal is
detected from other available sources, the Display will
turn off automatically after completing a cycle.
How to install No Signal Image
Install the file you want to use onto the root
directory of any USB storage device and name it
as "NoSignalImage.png". Connect the USB storage
device to the Display. Highlight the USB Operations
option in the Display Settings > Options > USB menu
and press OK.
No Signal Timer: You can define a shut-off timer for
the Display using this option. When the Display is
in No Signal state and No Signal OSD is displayed
on the screen, it will go into standby mode after the
time set here has expired.
Control Button Lock: Set to On to prohibit the use of
the button/s on the Display.
Remote Control Lock: Set to On to inhibit the use
of the remote. Remote control will function in standby
mode independently from the setting of this option.
To turn this option off and be able to use the remote
again, tap on the Display Settings widget on the Home
Screen, enter the Options > Controls menu and set
this option to Off.
UART0: Select ASCII/HEX protocol for UART 0.
Default value is ASCII. There is no need to restart
the Display after selection in order to work with the
protocols correctly. If the selection is changed, the
latest selected protocol will be preserved and started
when the Display is booted up.
Note that ASCII/HEX selection is not working while
debug logs are enabled. If it is wrongly changed to HEX
while debug logs are enabled, revert the selection to
ASCII and reboot the Display in order to correct the
debug logs and the ASCII protocol behaviour.
Also note that HEX protocol will work with the baud
rate value 19200 for UART 0.
UART1: Select ASCII/HEX protocol for UART 1.
Default value is HEX. There is no need to restart
the Display after selection in order to work with the
protocols correctly. If the selection is changed, the
latest selected protocol will be preserved and started
when the Display is booted up.
Note that ASCII/HEX selection is always working as
expected. It does not matter if the debug logs are
enabled or not.
Also note that HEX protocol will work with the baud
rate value 9600 for UART1.
Embedded Touch: Enable the functionality of the
embedded touch screen for the selected option. If set
to Auto, touch screen will be active for the current
source (External/USB Type-B, OPS, Display/Home,
or TypeC).
Microphone and Front USB (depends on the
model): Set your preference for the usage of the USB
input/s and microphone located on the front side of the
Display. Display, OPS, and Auto options are available.
Selected option determines whether the microphone
and front USB input/s are active.
Display - active for Home source
OPS - active for OPS source
Auto - active for current source (Home or OPS)
Note: Microphone and front USB may not be available
depending on the model of your Display.
Menu Lock: You can block the usage of the menu
button on the remote by setting this item as All menus.
When you press the Menu button on the remote, tap
on the Display Settings widget on the Home Screen,
or on the Settings Board, you will be asked to enter
the PIN that you have defined during the initial setup
process. If you didn't defined a PIN during the initial
setup, you can use the default PIN. Default PIN is set
to 0000. Set to Off to disable this function.
Auto Source Switch: If this option is enabled the
Display will switch to the currently active HDMI source
automatically when a device is connected to the
Display through the HDMI1 or HDMI2 input socket.
Set to Enabled to enable this feature.
When the HDMI source is removed the Display will
switch to other active HDMI source. If there isn't any
other device connected to the Display and the HDMI
Wake UP option for the related HDMI source is enabled
the Display will switch into the standby mode.
There is also a 3-second restriction for the successive
connected HDMI sources. This means, second HDMI
device must be plugged in 3 seconds after the first
HDMI device is plugged in.
Note: This feature applies for HDMI1 and HDMI2 input sockets
only. Refer to the General View section to see the HDMI inputs.
Bluetooth: Switches on or off the Bluetooth function-
ality. Set to Enabled to enable this feature.
English - 20 -
Publicité
