Publicité
Les langues disponibles
Les langues disponibles
General Use
The initial setup, the Settings and the Display Set-
tings menus are not fully compatible with the touch
screen. So it will be more convenient to use the remote
control when navigating through these menus and
performing initial setup process.
To interact with the user interface when on the Home
Screen or when working in an application, tap, tap
and hold or tap and drag with the included pen or your
finger. The Display also supports multitouch gestures
and more, so you can use two fingers to resize or
rotate objects, zoom in and out, and two or more
users can simultaneously write or draw while using
the applications or annotation tool.
Operation with the Remote Control
Press the Home button to display or return to the Home
Screen. You can only navigate through the elements
situated in the centre of the Home Screen using the
remote control buttons. Press the Right directional
button first to start navigating on the Home Screen
with the remote. Press the Menu button to display the
Display Settings menu. Use the directional buttons
to move the focus, proceed, adjust some settings and
press OK to make selections in order to make changes,
set your preferences, enter a sub-menu, launch an
application, etc. Press the Back or Exit button to return
to the previous menu screen or step, close a menu or
exit an application, etc.
Input Selection
Once you have connected external systems to your
Display, you can switch to different input sources.
Press the Source button on your remote control. Use
the directional buttons to highlight a source option and
press the OK button to switch to that source. Or expand
the General Tools Bar on the Home Screen, then tap
on the Source button. Available source options will be
displayed. Tap on any input source option to switch to it.
Adjusting the Volume and Brightness
You can adjust the volume by using the Volume +/-
buttons on the remote or on the front side of the Display
(depends on the model) and the brightness by using
the Brightness +/- buttons on the remote.
Note: Adjusting the brightness will not affect the picture on
the launcher menu.
You can also adjust the volume and brightness using
the dedicated sliders on the Settings Board. Tap on the
Settings button on the General Tools Bar to display
the Settings Board.
Initial Setup
When turned on for the first time, initial setup should be
performed. Follow the on-screen instructions to setup
your Display. The installation wizard will guide you
through the setup process. Use the directional buttons
and the OK button on the remote to select, set, confirm
and proceed. You can use the Back button to go back
to the previous steps and change your selections.
1. Language
The language selection options will be listed on the
screen. Select the desired language from the list and
press OK to continue.
2. Country
In the next step select your country from the list and
press OK to continue.
3. Login
You will be asked to define a PIN at this point. Enter a
PIN twice for confirmation using the virtual keyboard.
You have to enter this PIN if you are asked to enter a PIN
for any menu operation later. To skip this step highlight
Skip Pin and press OK.
4. Options
The Options Settings menu will be displayed next.
The NTP server can be configured using the related
option here. You can also see the model name, serial
number, and software version information about
your Display on this screen. You can save the model
information data of your Display to a connected USB
storage device using the Save model information
option. You can also copy database files from a
connected USB storage device to your Display using
the Clone from USB option. Refer to the Options
section for more information on the options of this
menu. After the settings are completed, highlight Next
and press OK to continue.
5. Display Operation Mode
The Display Operation Mode selection screen will be
displayed next. For normal operation set the Power
Mode to Reactive. Set to Eco for an energy-efficient
operation. In this mode your Display's settings will be
configured to reduce the energy consumption. Note
that, the UART/LAN Commands will not work if the
Display is in Eco mode. Highlight Next and press OK
to continue.
6. Network/Internet Settings
The Network/Internet Settings screen will be dis-
played. Refer to Network & Internet and Connectiv-
ity sections if you need information on configuring a
network connection and other available options. If you
want your Display to consume less power in standby
mode, you can disable the Networked Standby
Mode option by setting it to Off. After the settings are
completed highlight Next and press OK to continue.
7. Manufacturer Usage & Diagnostics
You will be asked to give your consent to the collection
of your data. Read the text on the screen for detailed
English - 12 -
Publicité
