Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Set up of the remote control.
Keep pressing the "+" button of the remote control and then connect
the cooker hood, to confirm that the remote control has been
recognized a long beep is issued. If you do not hear the acoustic
signal within 30 seconds, please repeat the steps as described.
Functions of the remote control.
The +, -,
and Light Push button have the same functions as on the
controls of the hood.
The
: Push button has the same function as the
Interval Function:
A specific function of this appliance is the Interval Function which
consists in activating the motor in automatic way 10 minutes each
hour at the speed flashing in the display.
This function can be activated on the control of the hood or by
remote control.
Interval Function by controls:
Keep pressing at the same time the O and + push buttons, then
release them: the display will show the 1;
Keep pressing at the same time the + push button, the display
will show the following for the speeds of the motor 2→3→1→2 ...;
Keep pressing at the same time the O and + push buttons to
confirm the speed for the motor you wish for the interval
function.
Interval Function by remote control:
Keep pressing the
: push button. The display will show 1;
Keep pressing the + push button, the display will show the
following for the speeds of the motor 2→3→1→2 ...;
Press the
push button to confirm the speed of the motor for
the interval function.
When you are in the setting phase, if the interval function shown is
not confirmed within some seconds, then you get out of the setting
mode for the interval function.
By pressing any push button, light excluded, the interval function is
excluded.
The remote control has a battery – When the battery is exhausted you
need to:
1.
loosen the 2 screws on the rear part and remove the cover.
2.
take the battery out and replace it with one with the same
characteristics.
3.
Close the cover again and tighten the screws.
Follow National norms for waste disposal of exhausted batteries.
Filters and maintenance
Caution:
As shown in the M figures of the mounting manual the panel must be
removed and remounted with 2 hands, keeping it parallel.
To open the panel just one side or with 1 hand (as shown on the
crossed out figures) can compromise the integrity of the closing
system.
Grease filters:
Metal filters are used to trap the greasy element of the vapours
that develop during cooking.
The filter mats are made from non-combustible metal.
Caution:
As the filter becomes more and more saturated with grease, not only
does the risk of catching fire increase, but the efficiency of the
extractor hood can also be adversely affected.
Important:
By cleaning the metal grease filters at appropriate intervals, the
possibility of them catching fire as a result of a build-up of heat such
as occurs when deep-fat frying or roasting is taking place, is reduced.
All manuals and user guides at all-guides.com
.
Saturation indicator:
When the grease filters are saturated
hood off, then the acoustic signal is removed.
The grease filters should be cleaned straight away.
Cleaning the metal grease filters:
In normal operation (1-2 hours daily) the metal grease filter must
be cleaned 1x a month.
The filters can be cleaned in a dish washer. It is however
possible that they become slightly discoloured.
The filters must be placed loosely and NOT wedged in the
dishwasher
Important: Metal filters that are saturared with grease should
not be washed together with other dishes.
When clearing the filters by hand, soak them in hot soapy water
first of all. Do not use aggressive, acidic or caustic cleaners.
Then brush the filters clean, rinse them thoroughly and leave the
water to drain off.
Removing and installing the metal grease filters:
1.
Follow the steps shown in the M figures.
2.
Depress the handles on the grease filters and fold down the
grease filters.
3.
Clean the grease filters.
4.
Re-install the cleaned grease filters.
5.
Clearing the
display.
Press 2x in succession the O push button. An acoustic
signal is issued and the
Cleaning and care
Isolate the extractor hood by pulling out the mains plug or
switching off the fuse.
Do not clean the extractor hood with abrasive sponges or with
cleaning agents which contain sand, soda, acid or chlorine.
Clean the extractor hood with a hot soap solution or a mild
window cleaner.
Do not scrape off dried-on dirt but wipe off with a damp cloth.
When clearing the grease filters, remove grease deposits from
accessibile parts of the housing. This prevents the risk of fire
and ensures that the extractor hood continues operating at
maximum efficiency.
Note: do not use alcohol (spirit) on plastic surfances, as dull
marks may appear.
Caution! Ensure that kitchen is adequately ventilated. Avoid
naked flames.
Clean the operating buttons with a mild soapy solution and soft,
damp cloth only.
Do not use stainless-steel cleaner to clean the operating buttons.
Stainless Steel surfances:
Use a mild non abrasive stainless steel cleaner.
Clean the surface in the same direction a sit has been ground
and polished.
flashes. If you switch the
display goes out.
11
Publicité
Table des Matières
