Backrest; Lap Belt - Quickie ARGON Notice D'utilisation

Übersicht

backrest

height-adjustable push handles
(Fig.6.24)
These handles are secured with
pins to prevent them from sliding
out uninten tion ally. Opening the
quick-release lever (1) makes it
possible to adjust the push handles
to meet your individual needs. As
you move the lever, you will hear a
locking mecha nism; you may now
easily position the push handle as
desired. The nut (2) on the tension
lever determines how tightly the push handles are clamp ed into
place. If the nut is loose after adjusting the tension lever, the
push handle will also be too loose. Turn the push handle from
side to side before use to make sure that it is clamped securely
enough into place. After adjusting handle height, always clamp
the tension lever (1) securely into place. If the lever is not
secure, injuries could result when ascending stairs.
fold-down push handles
(Fig.6.25)
If the push handles are not in
use, they can be folded down by
depressing the button (2). When
they are needed again, simply
flip them back up until they click
into place.

lap belt

Before using your wheelchair
ensure the lap belt is worn.
The lap belt must be checked on
a daily basis to ensure it is free
from any obstruction or adverse
wear.
Always make sure that the lap
belt is correctly secured and
adjustedprior to use. Too loose
a strap could cause the user to
slip down and risk suffocation or
cause serious injury.
The lap belt is ftted to the wheel-
chair as shown in the illustrations.
The seat belt comprises 2 halves.
They are ftted using the
existing seat stay retaining bolt
ftted through the eyelet on the
belt. The belt is routed under the
rear of the side panel. (Fig.6.26)
Adjust the belt position so buckles
are in the centre of the seat. (Fig.
6.27)
14 ARGON
3
1
2
Fig.6.24
Fig.6.25
2
Fig.6.26
Fig.6.27
adjust lap belt to suit the user's needs as follows:
To reduce the belt
length
Feed free belt back Feed free belt through slide adjusters and
through male buckle male buckle to provide more belt length.
and slide adjusters.
Ensure belt is not
looped at male
buckle.
When fastened check space
between the lap belt and user.
When correctly adjusted it
should
not be possible to insert more
than
the fat of the hand between the
lap belt and the user. (Fig.6.29)
The lap belt should be fxed so
that the belt sits at an angle of
45 degrees across the users
pelvis. The user should be
upright and be as far back
as possible in the seat when
correctly adjusted. The lap belt
should not allow the user
to slip down in the seat.
(Fig.6.30)
To fasten buckle:
Firmly push male buckle into
female buckle.
If in doubt about the use and operation of the lap belt
!
then ask your healthcare professional, wheelchair
dealer, carer or attendant for assistance.
advice to client
The lap belt must only be fitted by an approved Sunrise Medical
dealer / agent. The lap belt should only be adjusted by a
professional, or a Sunrise Medical approved dealer / agent.
The lap belt must be checked on a daily basis to ensure it is
adjusted correctly and free from any obstruction or adverse
wear.
Sunrise Medical does not encourage the transportation of any
person in a vehicle using this lap belt as a method of restraint.
Please see Sunrise Medical transit booklet for further advice on
transportation.
maintenance:
Check lap belt, and securing components, at regular intervals
for
any sign of frays or damage. Replace if necessary.
note:
The lap belt should be adjusted to suit the end user as detailed
above. Sunrise Medical recommend that the length and fit of the
belt be checked on a regular basis to reduce the risk of the end
user inadvertently re-adjusting the belt to an excessive length.
To increase the belt length
Fig.6.28
Fig.6.29
Fig.6.30
To release belt:
Press exposed sides of male
buckle and push towards
centre whilst gently pulling
apart.
Fig.6.31
0505/2/ST-000690645.EMS 1B