Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
When the input is unbalanced the control unit revers-
PULSE ON+OFF
es the on/off status of the areas associated with the input
The on/off status of the areas associated with the
STABLE ON+OFF
input follows the input's balancing status If the input is unbalanced
the areas are on, if it is balanced, they are off
Example: see the example given for the type of input
described as
.
SWITCH ON
Input description
INPUT
DESCRIPTION 001
Lets you edit the description of the input
With the
keys you can move horizontally, with the alphanumer-
(+)/(-)
ic keys you can edit the description letter by letter
Outputs
The valid procedure for all programming of outputs, after accessing
the Installer/Technical menu, is as follows:
OUTPUTS 12
MODIFY OUTPUT 001 OUTPUT 001
(▲)/(▼)
(*)
the output to be programmed (hereafter output
finally with
choose the property to be programmed Selecting
(▲)/(▼)
the value is done with the
(+)/(‒)
shows the default value of the property With
time
Status
TYPE
STABLE
The activity of the output follows the status of the associated
STABLE
event
Example: the output is activated by the associated in-
put's OPEN condition.
The activity of the output is determined by the associated event
PULSE
but only for a certain time, the duration of which can be selected
In the following table activations of the "output types", depending
upon the programming of the control unit, are shown
Output association for
Areas status
Input status
User code
Key
Failures
Scenario
TC
A pulse output associated with an event that lasts less than
the pre-set time will follow the PULSE TIME set for the output itself,
thereby ignoring the event time
The association of a stable output with a scenario, code or key type
event, will make the output a step output
Example for event code: When the code is entered on
the keypad, the output will be energised and it will re-
main so until it is de-energised at the next code entry,
and so on (toggle).
001
(*)/(#)
; with
choose
(▲)/(▼)
) and press
001
keys The display illustrated always
you can exit at any
(#)
001
(+)/(-)
STABLE
PULSE
x
x
x
x
x
x
x
x
x
x
x
x
x
-
Activation duration
PULSE
[0..255] SEC 000
Duration time of pulse output activation
Parameter visible only if the output is the pulse type
Example: you want to open a door lock with a code.
Associate a pulse output with an activation time of 3
seconds with a code.
Activation delay
ARMING
[0..255] SEC 000
Delay time between the activation command and the output's ac-
tivation
Parameter visible only if the output is the stable type
Deactivation delay
;
(*)
DISARM
[0..255] SEC 000
Delay time between the deactivation command and the output's
deactivation
Example: you want to view the on/off status of the
system via an output. In the Output Association menu
assign the areas' switch-on status to an output pro-
grammed as stable and with zero second delays on
activation and deactivation.
Security
SECURITY
The output is normally deactivated and is activated when it
NEGATIVE
is commanded
Example: by connecting a relay to an open collector
output with NEGATIVE SECURITY, the relay will normal-
ly be de-energised and will energise only when the
output is activated.
The output is normally active and is deactivated when it is
POSITIVE
commanded
Example: by connecting a relay to an open collector
output with POSITIVE SECURITY, the relay will normally
be energised and will de-energise only when the out-
put is activated.
Remote activation
REM. ACTIV.
If activated it lets you remotely activate the output via voice guide
or SMS
Example: you want to activate a pulse-type output via
SMS to switch on the heating.
Code 1: code
123456
Output 2:
type; remote activation
PULSE
Phone options: remote control by SMS
SMS to be sent:
TIME
001
(+)/(-)
DELAY
001
(+)/(-)
DELAY
001
(+)/(-)
001
NEGATIVE
(+)/(-)
001
NO
(+)/(-)
; remote control
.
YES
.
YES
.
YES
heating on.CRSMS.123456.6002.
Publicité
Table des Matières
