Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Input modules
INPUT MODULES
--
To enable/disable any input expansion modules, local and on bus
With number key
select the expansion of the module in the con-
(1)
trol unit With number keys
(2)
modules on the bus
Example: if we activate module 1 (expansion in control
unit) the display will show
If we activate the expansion in the control unit and one
on the bus the display will show
Installed module
INSTALLED MODULE
--
Select which module - the PX8I or the PX8IR (with address 1) is
installed
Output modules
OUTPUT MODULES
--
To enable/disable any output module expansions
With the number keys
you can select the output modules to
(0)
(9)
be managed
To set outputs above
, for example output
(9)
keys
(0)
(3)
Example: if we activate an expansion in the control unit
and one on the bus the display will show
Radio modules
RADIO MODULES
--
To enable/disable any expansion radio modules connected on the
Bus (maximum 2)
With the number keys
(module1 is the one local to the con-
(2)
(3)
trol unit and cannot be enabled/disabled) you can select the radio
modules to be managed
Example: if we key in 2 the display will show
system will include radio module1 of the Control Unit
(not displayed) and radio module 2 on the Bus.
Radio sirens
RADIO SIRENS
--
To enable/disable any radio sirens that can be connected (maxi-
mum 4)
With the number keys
(siren 1 is the first radio siren connect-
(2)
(4)
ed) you can select the radio sirens to be managed
Addressing keypads
All the remote keypads leave the factory with address 1 Going
straight from the remote keypad menu there is an option to change
the address:
Press key
for a few moments; with the
(*)
menu and with the
ADDRESS
(+)/(-)
Carry out this operation on all the keypads present
(0)/(9)
select the expansion of the input
(9)
.
#-
.
##
(0)/(9)
(0)/(9)
, press the number
(13)
.
##--
(1)/(2)
. The
#-
(2)/(4)
keys select the
(▲)/(▼)
keys choose the address you want
The change keypad address menu can be modified within 4
minutes of first start-up of the device
Readers auto-recognition
ON
READER XX
APPROACH KEY
If the readers are not configured,
displayed on the keypad
Go onto the remote reader indicated and approach a transponder
key until the reader confirms with a beep
on the control unit display
After a few seconds it will automatically move on to addressing the
2nd reader (if necessary), otherwise press
will display them in rotation, emitting a beep for each one
Inputs test
INPUTS TEST
*=LAUNCH TEST
AREAS TO TEST
###
The open inputs test can be carried out on the whole system or just
on some selected areas
Once key
is pressed to start the inputs test, before displaying the
(*)
choice of areas to be tested the keypad will display the message
for a few seconds, to allow the various devices con-
WAITING FOR SYNC.
nected to the control unit to get into alignment with the baud rate
With the number keys
you can enable/disable areas
(1)
(3)
Example: if we key in 2 the display will show
test will be carried out only on areas 1 and 3.
Control unit tamper test
Lets you check the control unit tamper status
C.U. TAMP. TEST
*=LAUNCH TEST
Control unit battery test
Lets you quickly check the control unit battery status
C.U. BATT. TEST
*=LAUNCH TEST
Sirens test (for hard-wired sirens only)
The test enables you to manually control the control unit alarm relay
output
SIRENS TEST
*=LAUNCH TEST
Outputs test
OUTPUTS TEST
*=LAUNCH TEST
The test enables you to manually control the system's outputs
READER OK
PRESS */OK
will be
ON READER XX APPROACH KEY
will appear
READER XX OK
to quit The system
(#)
(*)
(1)...(3)
. The
#-#
(*)
(*)
(*)
(*)
Publicité
Table des Matières
