Gaggia Baby Twin Mode D'emploi page 19

ENGLISH
Pre-Infusion
The machine allows you to adjust the dosage settings so
that the water produced for the COFFEE dose is preceded by
a pre-infusion step.
Press the dose button (2) and the normal coffee cycle is
preceded by a brief, timed jet of water that moistens the coffee
wafer before the actual coffee making cycle starts.
This function allows you to get the most fl avor out of the
coffee wafer.
PRE-INFUSION is not available on the dose button (3).
N.B.: the machine comes from the factory with PRE-INFUSION
function set to ON. Should you choose to deactivate this
function you will need to enter the programming mode
(see "Coffee dose programming") and press the
hot water supply button (4). The indicator light on the
button will turn off.
The indicator light on the hot water supply button (4) is
ON when the PRE-INFUSION function is ON. Vice versa, if
the indicator light is OFF, then the PRE-INFUSION function
is OFF.
Coffee preparation
1 Follow the procedure described under "Prepara-
tion".
2 Insert the frothing jet device (13) into the fi lter holder
(9).
Insert the "Perfect crema" fi lter for ground coffee (11) into
the fi lter holder, both for brewing 1 or 2 coffee cups.
Insert the fi lter holder (9) into the brew group (14) from
the bottom and wait for it to heat up.
3 Place a container under the fi lter holder (9). Preheat the
fi lter holder by pressing button (6) (this operation is
only necessary for the fi rst coffee).
Water will start coming out.
4 After dispensing 150 cc of water, press button (6) again
to stop dispensing.
5 Wait for the machine to reach the correct temperature
with the fi lter holder cup inserted (warm-up time is about
6 minutes).
In the meantime, prepare cups, milk and coffee, etc.
6 After the warm-up period, remove the warm fi lter-holder
(9) from the brewing head and fi ll with correctly ground
espresso coffee using the measuring spoon provided.
Place one level measure of coffee in basket for each cup
of espresso. Do not overfi ll. Gently tamp down coffee with
the tamper (18) provided. Do not compress too fi rmly.
7 Clean any excess coffee from the rim of fi lter holder (9).
Insert fi lter holder into brew head by holding handle ap-
proximately 45 degrees to the left as you face machine.
When properly aligned,move handle fi rmly to the right
to lock into position.
The handle should point to the front of the machine or
slightly to the right.
8 Place one or two espresso cups on the drip plate to line
up with the spouts of the fi lter holder. Press the button
corresponding to the stored coffee dose. Espresso will
start to fl ow into cups.
9 The coffee dispensing will automatically stop when
the preset level is reached (see Coffee dose
programming);however it is possible to stop the
coffee dispensing by pressing the button (2 or 3) as
previously selected. When properly made, the espresso
will have a light brown foam "crema" fl oating on the
top.
If not, refer to "In the event of faulty function".
10 Remove cups and serve.
11 To brew more coffee, slowly remove the fi lter holder with
caution, moving it towards the left. Make sure to not get
burnt with the water from coffee grounds. Once the fi lter
holder has been removed, some water will still drop. This
is due to the water pressure in the system. Remove the
grounds from the fi lter. To brew more coffee, repeat the
procedure from step 6 to 10.
12 To brew coffee in manual mode repeat the procedure
from step 6 to 7 and then press button (6). Once the
desired dose has been reached, press button (6) again
to stop brewing. Then proceed with steps 9 and 10.
N.B.: Dispensing should not exceed 40 seconds.
• 16 •