Publicité
Les langues disponibles
Les langues disponibles
EngLIsh
3. Replace and securely tighten the 4 guard screws
the wrench
17
as shown in figure I.
4. Replace the spool housing as described in the Attaching
Spool Housing section below.
Attaching spool housing (Fig A, I, J)
1. Slide the string trimmer drive washer (small)
the the bolt
26
protruding from the trimmer so that its hole
21
lines up with the hole
2. Rotate the washer and motor housing until their holes line
up with the notch
in the guard
27
3. Insert a screwdriver through the three holes, thread the
spool housing counterclockwise, and securely tighten onto
the bolt.
Attaching blade (Fig. A, K)
WARNING: Risk of injury. Brush cutter blade has sharp
edges. Wear gloves when handling blade.
1. Remove the spool housing
washer (small)
20
as described in the Removing the spool
housing section.
2. Slide the brush cutter drive washer (large)
the the bolt
26
protruding from the trimmer so that its hole
29
lines up with the hole
3. Slide the brush cutter blade
so that the inner, non-cutting edge
hole of the drive washer. This will allow for easier and safer
removal of the blade later.
4. Slide the brush cutter clamp washer
so that the wider side is flat against the blade.
5. Screw the brush cutter nut
wrench
17
. Ensure the nut is securely tightened.
6. Slide the cotter pin
fully through the hole in the bolt.
33
Attaching auxiliary handle (Fig. A, L)
1. Place the auxiliary handle
6
pole
8
above the label placed in the middle fo the pole.
2. Slide the bracket
34
of the auxiliary handle into the bottom
of the handle.
3. Thread the handle bolts
35
the handle.
4. Tighten the handle bolts with the wrench
handle is securely attached.
If adjustment is necessary, loosen the handle bolts and slide the
auxiliary handle up or down the trimmer pole. Then, retighten
the bolts.
Replacing guard (Fig. I, M)
1. Remove the spool housing
Removing the spool housing section.
2. Remove the 4 guard screws
3. Lift the guard off at an angle as shown in figure M.
4. Install the new guard as described in the Attaching
guard section.
36
with
25
down over
20
22
in the motor housing
7
.
.
11
12
and the string trimmer drive
down over
28
22
in the motor housing
7
.
16
on top of drive washer
lines up with the
30
on top of the blade
31
32
onto the bolt with the
onto the top of the trimmer
through the bracket and into
. Ensure the
17
12
as described in the
25
shown in figure I.
Attaching strap (Fig. A)
Hook the strap
10
to the strap mount
one shoulder for extra support while using the trimmer or
brush cutter.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. A, O)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the handle
the other hand on the auxiliary handle
Switching On (Fig. A)
To turn the appliance on, push the lock off tab
squeeze the lock-off lever
2
, and then squeeze the variable
speed trigger
.
1
To turn the appliance off, release the variable speed trigger, the
lock-off lever, and tab.
Speed Control Switch (Fig. A)
This string trimmer gives you the choice to operate at a
more efficient speed to extend the runtime for larger jobs, or
accelerate the trimmer speed for high-performance cutting.
To extend runtime, push the speed control switch
toward the auxiliary handle
6
is best for larger projects that require more time to complete.
To accelerate the trimmer, pull the speed control switch back
toward the battery housing
13
is best to cut through heavier growth and for applications that
need higher RPM.
nOTE: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO" mode.
Trimming / Brush cutting (Fig. A, N, O)
With the trimmer on, angle it and swing side to side as shown
in figure N.
Maintain a minimum distance of 610 mm between the guard
and your feet as shown in figure O.
WARNING: Keep the rotating string roughly parallel with
the ground (tilted no more than 30 degrees). This trimmer is
not an edger. DO NOT TILT the trimmer so that the string or
brush cutter blade
16
is spinning near a right angle to the
ground. Flying debris can cause serious injury.
9
and place strap on
4
, with
6
.
3
forward,
forward
5
into the "LO" position. This mode
into the "HI" position. This mode
Publicité
