DeWalt DCM571 Traduction De La Notice D'instructions Originale page 37

Keep bystanders away.
Directive 2000/14/EC guaranteed
sound power.
Date Code Position (Fig. U)
The date code 45 , which also includes the year of manufacture,
is printed into the housing.
Example:
2017 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Variable speed trigger
1
Lock-off lever
2
Lock-off tab
3
Handle
4
Speed control switch
5
Auxiliary handle
6
Motor housing
7
Trimmer pole
8
Strap mount
9
Strap
10
Guard
11
Spool housing
12
Battery housing
13
Battery pack
14
Battery release button
15
Brush cutter blade
16
Nut wrench
17
Blade cover
18
Intended Use
Your string trimmer / brush cutter has been designed for
professional trimming applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. C–E)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool
1. Align the battery pack 14
(Fig. C).
2. Slide it into the tool until the battery pack is firmly seated
and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 15
out of the tool handle (Fig. D).
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. E)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
19 . A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Assembly
Removing spool housing (Fig. A, F, G)
1. Insert the rod through the hole
46
drive washer (small) 20 and into the hole
housing 7 as shown in figure F.
2. Turn the spool housing 12
3. Remove the spool housing and the drive washer from
the trimmer.
Attaching guard (Fig. A, H, I)

WARNING: Never operate appliance without guard firmly
in place. Damage or personal injury could result.
1. Remove the spool housing
Removing the spool housing section.
2. To attached the guard, slide the tab
the lip of the motor housing
24
the guard into place as shown in figure H.
EngLIsh
WALT battery packs and chargers.
is fully charged.
14
with the rails inside the tool
and firmly pull the battery pack
in the string trimmer
21
22 in the motor
clockwise as shown in figure G.
12 as described in the
23 of the guard under
, then lower the back of
7
35