Scheppach CRS450-20ProS Traduction Des Instructions D'origine page 22

Switching on and off
Ensure your stance is stable and hold the device
tightly with both hands and away from your body. Be-
fore switching the device on, ensure it is not in con-
tact with the work piece.
Switching on:
1. Ensure that the battery (11) is inserted (see "Re-
moving/inserting the battery").
2. Press the switch lock (9) and the on/off switch (8),
then release the switch lock (9).
3. By using the on/off switch (8) you can progres-
sively control the stroke rate.
Gentle pressure: low stroke rate.
Greater pressure: higher stroke rate.
The on/off switch cannot be locked.
Switching off:
4. Release the on/off switch (8).
Adjusting the base plate
To adapt to the work piece, the base plate can be
adjusted and swivelled to 4 positions.
1. Press the adjusting button (5).
2. The base plate (2) can now be adjusted to the de-
sired position. It can now be felt locking into place.
3. The base plate (2) can be pivoted by applying light
pressure.
Switching on/off the oscillating function
To improve the progress of the sawing process, an
oscillating motion can be switched on.
Sawing without oscillation:
• For thin, hard work pieces such as wooden boards.
• In order to achieve cleaner cut edges.
Sawing with oscillation:
• For processing work pieces with medium and soft
strength, such as soft and hard wood, tree wood,
insulation material.
Switching on the oscillating function:
1. Turn the rotary switch (6) to position "1".
Switching off the oscillating function:
2. Turn the rotary switch (6) to position "0".
Conventional sawing:
1. Turn the device on. Before switching the device
on, ensure it is not in contact with the work piece.
2. Place the base plate on the work piece.
3. Cut with a uniform forward motion. You can saw
horizontally (see ), diagonally or vertically (see ).
4. After completion of the work, first remove the
blade from the saw cut and then switch the device
off.
22 | GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Plunge sawing:
Plunge cuts are technically more demanding and har-
bour a greater risk. Only perform this work if you are
familiar with this technique.
Plunge cuts may only be carried out in soft ma-
terials such as wood or plasterboard and with
short blades (max. length 150 mm). There is a
risk of kickback and personal injury.
1. Place the front edge of the base plate (2) on the
work piece so that the saw blade (1) does not
touch the work piece.
2. Turn the device on and let the saw blade (1) slowly
plunge into the work piece.
3. When the work piece depth has been cut through,
continue sawing as usual.
Flush separation:
With elastic bi-metal saw blades (see spare parts/
accessories) you can separate water pipes, for ex-
ample, flush to the wall.
Make sure that the blade is always longer than
the pipe diameter. There is a risk of kickback and
personal injury.
9. Cleaning
Danger!
Always pull out the battery pack before starting any
cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device. The ingress of water into an electric tool
increases the risk of an electric shock.
10. Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag-
ing. Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.
11. Maintenance
There are no parts inside the equipment which re-
quire additional maintenance.