Yamaha SPX2000 Mode D'emploi page 93

■ 2.8.2.10 Parameter change (Function call : Program
clear)
When the SPX2000 receives this message, it will erase the specified effect
name, and will then use this message to transmit the state following the
change. At this time, the device number will be the MIDI channel of the
SPX2000. If the MIDI channel is OMNI, the device number will be 1.
• Format
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUP ID 00011110 1E
MODEL ID 00001001 09
ADDRESS 00010000 10
01100100 64
0mmmmmmm mh
0mmmmmmm ml
EOX 11110111 F7
function
Effect Program Clear 0x64
■ 2.8.2.11 Parameter change (Function call : Undo)
When the SPX2000 receives this message, it will perform the same opera-
tion as if the [UNDO] button had been pressed, and will then use this
message to transmit the state following the change. At this time, the
device number will be the MIDI channel of the SPX2000. If the MIDI
channel is OMNI, the device number will be 1.
• Format
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUP ID 00011110 1E
MODEL ID 00001001 09
ADDRESS 00010001 11
00100010 24
00000000 00
00000000 00
DATA 00000000 00
00000000 00
EOX 11110111 F7 End of exclusive
■ 2.8.2.12 Parameter change (Function call : Compare)
When the SPX2000 receives this message, it will perform the same opera-
tion as if the [COMPARE] button had been pressed, and will then use this
message to transmit the state following the change. At this time, the
device number will be the MIDI channel of the SPX2000. If the MIDI
channel is OMNI, the device number will be 1.
• Format
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUP ID 00011110 1E
MODEL ID 00001001 09
ADDRESS 00010001 11
01000100 44
00000000 00
00000000 00
DATA 00000000 00
00000000 00
EOX 11110111 F7
■ 2.8.2.13 Parameter change (Function call : Event
Effect)
When the SPX2000 receives this message while a freeze-type effect is
recalled, it will perform the same operation as if the RECORD parameter
or PLAY parameter is selected and the [▼ DEC] button pressed. The con-
tents of the function will determine whether the RECORD parameter or
the PLAY parameter is selected.
• Format
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUP ID 00011110 1E
System exclusive message
Manufacture's ID number
(YAMAHA)
n=0-15 (Device number=Device
No-1)
MODEL ID (signal processor)
SPX2000
Function call
Effect Program clear func-
tion
number High
number Low
End of exclusive
number
123-221
System exclusive message
Manufacture's ID number
(YAMAHA)
n=0-15 (Device number=Device
No-1)
MODEL ID (signal processor)
SPX2000
Function call
Undo
System exclusive message
Manufacture's ID number
(YAMAHA)
n=0-15 (Device number=Device
No-1)
MODEL ID (signal processor)
SPX2000
Function call
Compare
End of exclusive
System exclusive message
Manufacture's ID number
(YAMAHA)
n=0-15 (Device number=Device
No-1)
MODEL ID (signal processor)
MODEL ID 00001001 09
ADDRESS 00010010 12
0000ffff 0f
00000000 00
0ppppppp pp
DATA 00000000 00
0eeeeeee ee
EOX 11110111 F7
function
Freeze Play button 0x00
Freeze Record button 0x01
*This will not function if the effect type is wrong.
■ 2.8.2.14 Parameter change (Function call: attri-
bute(Protect))
When the SPX2000 receives this message, it will switch Protect on/off for
the specified effect, and will then use this message to transmit the state
following the change. At this time, the device number will be the MIDI
channel of the SPX2000. If the MIDI channel is OMNI, the device num-
ber will be 1.
• Format
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUP ID 00011110 1E
MODEL ID 00001001 09
ADDRESS 00010100 14
00000100 04
0mmmmmmm mh
0mmmmmmm ml
DATA 0ttttttt tt
0ttttttt tt
EOX 11110111 F7
function
Effect Program Attribute
■ 2.8.2.15 Parameter request (Function call: attri-
bute(Protect))
• Format
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0011nnnn 3n
GROUP ID 00011110 1E
MODEL ID 00001001 09
ADDRESS 00010100 14
00000100 04
0mmmmmmm mh
0mmmmmmm ml
EOX 11110111 F7
For the function and number, refer to the table in "2.8.2.14 Parameter
change (Function call: attribute (Protect))."
■ 2.8.2.16 Parameter change (Function call: LCD Back
Color)
When the SPX2000 receives this message, it will change the display
background color of the specified effect, and will then use this message
to transmit the state following the change. At this time, the device
number will be the MIDI channel of the SPX2000. If the MIDI channel
is OMNI, the device number will be 1.
• Format
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUP ID 00011110 1E
MODEL ID 00001001 09
ADDRESS 00010100 14
01100100 64
0mmmmmmm mh
0mmmmmmm ml
DATA 0ccccccc cc
0ccccccc cc
SPX2000—Mode d'emploi
SPX2000
Function call Effect Event
function
Release:0, Press:1
Effect number (0)
End of exclusive
channel
0
0
System exclusive message
Manufacture's ID number
(YAMAHA)
n=0-15 (Device number=Device
No-1)
MODEL ID (signal processor)
SPX2000
Function call
attribute
number High
number Low
attribute(protect:0x0001,
normal:0x0000)
End of exclusive
number
1-221(1-122:res-
0x04
ponse only)
System exclusive message
Manufacture's ID number
(YAMAHA)
n=0-15 (Device number=Device
No-1)
MODEL ID (signal processor)
SPX2000
Function call
attribute
number High
number Low
End of exclusive
System exclusive message
Manufacture's ID number
(YAMAHA)
n=0-15 (Device number=Device
No-1)
MODEL ID (signal processor)
SPX2000
Function call
LCD Back Color
number High
number Low
color(0:Green,1:Yellow,
2:Magenta,3:Cyan,4:White)
93