Connecting Other Wireless Devices - Kimex 164-6540 Manuel D'utilisation

other WLAN 11b appliances. The standard values of
the transmission speed are the theoretical maximum
values for the wireless standards. They are not the
actual speeds of data transmission.
• The location where the transmission is most effective
differs depending on the usage environment.
• The Wireless feature of the Display supports 802.11
a,b,g & n type modems. It is highly recommended
that you should use the IEEE 802.11n communication
protocol in order to avoid any possible problems while
watching videos.
• You must change your modem's SSID when there are
any other modems around with the same SSID. You
can encounter connection problems otherwise. Use
a wired connection if you experience problems with a
wireless connection.
Configuring Wireless Device Settings
Open the Network menu and select Network Type as
Wireless Device to start connection process.
Highlight Scan Wireless Networks option and press
OK to start a search for available wireless networks.
All found networks will be listed. Highlight your desired
network from the list and press OK to connect.
Note: If the modem supports N mode, you should set N
mode settings.
If the selected network is password-protected, enter the
correct key by using the virtual keyboard. You can use
this keyboard via the directional buttons and the OK
button on the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established.
To disconnect from a wireless network, highlight
Network Type and press Left or Right buttons to set
as Disabled.
If your router has WPS, you can directly connect to the
modem/router without entering a password or adding
the network first. Highlight Press WPS on your wifi
router option and press OK. Go to your modem/router
device and press the WPS button on it to make the
connection. You will see a connection confirmation
on your Display once the devices have paired. Select
OK to proceed. No further configuration is required.
Highlight Internet Speed Test and press the OK button
to check your internet connection speed. Highlight
Advanced Settings and press the OK button to open
the advanced setting menu. Use directional and numeric
buttons to set. Highlight Save and press the OK button
to save settings when complete.
Other Information
You can also enable or disable Wake On feature using
the related option. The status of the connection will
be displayed as Connected or Not Connected and
the current IP and MAC addresses, if a connection is
established.
Connecting to your mobile device via WLAN
• If available, you can download a virtual remote
controller application from the server of your mobile
device application provider.
Note: This feature may not be supported on all mobile devices.
Wake ON
Wake-on-LAN (WoL) and Wake-on-Wireless LAN
(WoWLAN) are technologies that allow a device to be
turned on or woken up by a network message(magic
packet). This message is sent to the device by a
program executed on a remote device connected to
the same local area network, such as a smartphone.
Your Display is WoL and WoWLAN compatible. To
enable this feature set the Wake On option in the
Settings/Network menu as On and set the Quick
Standby option in the Signage>Power Up Settings
menu as Disabled. It is necessary that both the
device, from which the network message will be sent
to the Display, and the Display are connected to the
same network. All devices must support magic packet
on the system from Access Points to the device which
sends the magic packet and the device which receives
the magic packet to wake-up. You can use any Wake-
on-LAN software available for the operating system of
your device in order to send magic packets.
How to control functionality
• Enable Wake On option from Settings>Network
menu by settings as On
• Connect your Display and the remote device, which
will send the magic packets to the Display, to the
same network
• Get the MAC address of your Display which will be
needed in order to send magic packets
• Switch the Display into standby mode
• Send magic packets to the MAC address of your
Display by using mobile phones, Linux or Windows
computers
Your Display should wake up after receiving magic
packets.

Connecting Other Wireless Devices

Your Display supports another short range wireless
connection technology too. A pairing is required before
using these kind of wireless devices with the Display
set. You should do the followings to pair your device
with the Display:
• Set the device to pairing mode
• Start device discovery on the Display
Note: Refer to the user manual of the wireless device to learn
how to set the device to pairing mode.
You can connect audio devices or remote controllers
wirelessly to your Display. Unplug or switch off any
English - 24 -