Important; Assembly And Starting; Setting The Pressure Switch - EINHELL TE-AC 36/6/8 Li OF Set Instructions D'origine

If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.

Important!

Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Installing the battery (Fig. 1b)
Flip up the battery cover (18) as shown in Figure
1b. Slot the two rechargeable batteries (12) into
the mounts.
Battery capacity indicator (Fig. 4)
Press the battery capacity indicator switch (a).
The battery capacity indicator (b) will indicate the
charge status of the battery by means of 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
Anl_TE_AC_36_6_8_Li_OF_SPK13.indb 18 Anl_TE_AC_36_6_8_Li_OF_SPK13.indb 18
GB
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.

6. Assembly and starting

Important!
You must fully assemble the equipment befo-
re using it for the fi rst time.
6.1 On/Off switch (Fig. 1a)
To switch on the equipment, set the On/Off switch
(8) to position 1.
To switch off the equipment, move the On/Off
switch (8) to position 0 .
6.2 Setting the pressure (Fig. 1a)
•
You can adjust the pressure on the pressure
gauge (6) using the pressure regulator (7).
•
The set pressure can be drawn from the
quick-lock coupling (5).

6.3 Setting the pressure switch

The pressure switch is set at the factory.
Cut-in pressure approx. 6 bar
Cut-out pressure approx. 8 bar
7. Operation
7.1 Tire pressure gauge with adapters (Fig. 2)
Working pressure in bar: 0 – 8
Range of applications:
The tire pressure gauge (15) allows you to infl ate
car tires easily and exactly. Use the pressure
gauge to check the tire pressure. If the tire pres-
sure is too high, you can reduce the pressure with
the integrated relief valve (e). The tire pressure
gauge comes with a valve adapter for car tire
valves.
Warning! Observe the information supplied by
the tire manufacturer and the vehicle manufactu-
rer relating to the recommended tire pressure.
Warning! This equipment is not calibrated! For a
calibrated measurement value, check the actual
tire pressure using a calibrated meter after you
have infl ated the tires yourself, e.g. at a petrol
station.
- 18 -
19.04.2022 08:43:54 19.04.2022 08:43:54