Amp Device Mode - Arcam AV860 Manuel

AMP Device Mode

The Device Mode button configures the remote to
AMP
control the Receiver. Pressing this button does not affect
the currently selected input on the Receiver.
The functionality of the remote is context sensitive for
the internal sources and is described in the following
table.
2 Single press – Toggles Receiver power
between standby and on in the current zone
(zone in which the command is received).
Press and hold – Forces all zones into
standby, regardless of which zone the
command was received in.
0......9 The number keys can be used for direct
entry of numeric values
Sync. Delays may be introduced into the
SYNC
video signal by video processing which
causes a mismatch between the audio and
video timing. You will notice this by speech
sound being out of synchronization with the
lip movements in the video. To compensate
for this, you can adjust the lip sync delay.
button and use the < and >
Press the SYNC
navigation buttons. Press again to exit the
lip sync trim menu.
INFO Info cycles through the information
displayed on the lower left portion of the
front panel display when on TUN, NET and
inputs.
USB
Brings up the DTS:X dialogue control
adjustment.
MENU Displays the unit's setup menu on the On
Screen Display.
POP UP Toggles Dolby Volume on/off.
AUDIO Toggles Dirac Live EQ on/off.
RTN Brings up a temporary subwoofer trim
control. Use the < and > navigation
buttons. Press again to exit the sub trim
RTN
control. As this is a temporary adjustment,
the sub trim level is reset to the value set in
the Speaker Levels menu when the unit is
turned off or put into standby.
Toggles the mute function of the AVR.
VOL Adjust amplifier volume.
MODE Cycles through the available surround and
downmix modes.
DISP Cycles through the front panel display's
brightness options
AMP Resets remote to AMP mode.
Stereo direct on/off. Provides a direct
DIRECT
analogue path from the analogue inputs to
the left and right front outputs. Switches off
any surround processing modes and shuts
down the DSP circuits for the best stereo
sound quality.
Navigate the files and menus on the screen.
OK selects the highlighted file or enters
the highlighted menu on the screen –
equivalent to 'Enter' or 'Select' on some
remote controls.
' Up
< Left
> Right
, Down
+ ' Power on from standby
AMP
+ , Standby from Power on
AMP
+ select Zone 2
AMP OK
RED Red button.
Green button.
GREEN
YELLOW Yellow button.
BLUE Blue button.
RADIO Tuner input.
Aux input.
AUX
NET Network (NET) input.
USB USB input.
AV AV input.
SAT SAT input.
PVR PVR input.
GAME Game console input.
BD input.
BD
CD CD input.
STB STB input.
VCR VCR input.
USB commands
The USB interface is selected by pressing USB
Device Mode on the remote. When connected to a
device storing music files connected by USB, the keys
below are used to navigating music tracks.
Navigates the files on screen.
selects/plays the highlighted file.
OK
9 Selects the previous/next track in the
current playlist.
:
4; Pause and playback of the current track.
Stops playback..
Network commands
When using the network client, the keys below are used
to navigate music files in Device Mode.
AMP
Navigates the files on screen.
selects/plays the highlighted file.
OK
9 Selects the previous/next track in the
current playlist.
:
4; Pause and playback of the current track.
Stops playback..
RED Adds the currently displayed radio station
to the favourites list when using the network
client.
GREEN Removes the currently displayed radio
station to the favourites list when using the
network client.
Returns navigation to the top level of the
network client menus ('Home')
E-22
in AMP