Bosch PPS 7S Mode D'emploi page 30

OBJ_BUCH-1259-004.book Page 30 Thursday, November 6, 2014 10:45 AM
30 | English
Safety Warnings for Pull Push Saws
 The power tool is provided with a laser warning label
(marked with number 2 in the representation of the
power tool on the graphics page).
EN 60825-1:07
<0.39mW, 650 nm
Laser radiation
Do not view directly
with optical instruments
Class 1M laser product
 Never make warning signs on the machine unrecognis-
able.
 Never stand on the power tool. Serious injuries can occur
when the power tool tips over or when inadvertently com-
ing into contact with the saw blade.
 Take care that the blade guard operates properly and
can move freely. Always adjust the blade guard in such a
manner that it faces loosely against the workpiece when
sawing. Never clamp the blade guard when it is open.
 Keep hands away from the cutting area while the ma-
chine is running. Danger of injury when coming in contact
with the saw blade.
 Never reach behind the saw blade in order to hold the
workpiece, remove saw dust/wood chips or for any oth-
er reason. The clearance of your hand to the rotating saw
blade is too small.
 Operation as a Pull Push Saw:
 Guide the saw blade against the workpiece only
when the machine is switched on. Otherwise there is
danger of kickback when the saw blade becomes
wedged in the workpiece.
 Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
 Operation as a Table Saw:
Guide the workpiece only against the running saw
blade. Otherwise, there is danger of kickback when the
saw blade becomes wedged in the workpiece.
 Keep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery causing loss of control.
 Operate the power tool only when the work area to the
workpiece is clear of any adjusting tools, wood chips,
etc. Small pieces of wood or other objects that come in
contact with the rotating saw blade can strike the operator
with high speed.
 Use the machine only for cutting the materials listed
under Intended Use. Otherwise, the machine can be sub-
ject to overload.
 Only saw one workpiece at a time. Workpieces placed on
top or aside of each other can cause the saw blade to jam
or the workpieces to move against each other while saw-
ing.
 Always use the universal guide. This improves the cut-
ting accuracy and reduces the possibility that the saw
blade becomes wedged or jams.
1 609 92A 0VR | (6.11.14)
 Use the machine for grooving or rebating only with an
appropriately suitable protective device (e. g. a tunnel
blade guard).
 Do not use the machine for cutting slots (stopped
grooves).
 For all cuts, firstly ensure that the saw blade cannot
touch or graze against the stops or any other machine
parts. When the saw blade becomes wedged or caught in
other machine parts, there is danger of kickback and the
power tool can be considerably damaged.
 If the saw blade should become jammed, switch the ma-
chine off and hold the workpiece until the saw blade
comes to a complete stop. To prevent kickback, the
workpiece may not be moved until after the machine
has come to a complete stop. Correct the cause for the
jamming of the saw blade before restarting the machine.
 Do not use dull, cracked, bent or damaged saw blades.
Unsharpened or improperly set saw blades produce nar-
row kerf causing excessive friction, blade binding and kick-
back.
 Always use blades with correct size and shape (dia-
mond versus round) of arbour holes. Blades that do not
match the mounting hardware of the saw will run eccentri-
cally, causing loss of control.
 Do not use high speed steel (HSS) saw blades. Such saw
blades can easily break.
 Do not touch the saw blade after working before it has
cooled. The saw blade becomes very hot while working.
 Never operate the machine without the insert plate.
Replace a defective insert plate. Without flawless insert
plates, injuries are possible from the saw blade.
 Check the cable regularly and have a damaged cable re-
paired only through an authorised customer service
agent for Bosch power tools. Replace damaged exten-
sion cables. This will ensure that the safety of the power
tool is maintained.
 Store the machine in a safe manner when not being
used. The storage location must be dry and lockable.
This prevents the machine from storage damage, and from
being operated by untrained persons.
Do not direct the laser beam at persons
or animals and do not stare into the di-
rect or reflected laser beam yourself, not
even from a distance. You could blind
somebody, cause accidents or damage
your eyes.
 If laser radiation strikes your eye, you must deliberate-
ly close your eyes and immediately turn your head
away from the beam.
 Do not use any optical instruments such as binoculars
to view the radiation source. Doing so can damage your
eye.
 Do not direct the laser beam at persons who are looking
through binoculars or similar instruments. Doing so can
damage their eye.
Bosch Power Tools