Warnings - Dräger Polytron 5000 Série Mode D'emploi

Fault Cause
number
E101 Firmware CRC
error
E102 / RAM error
Err102
Err 103 Flash memory
error
Err 104 Event logger error
Err 105 Analog signal con-
verter error
E106 Incorrect software
installed
E107 Power supply error Connect power supply
E108 4-20 output error
E109 Sensor failure
Err 110 Sensor interface
failure
Err 112 Zero calibration
failed
Err 113 Span calibration
failed
Err 115 Gas value is under
range
Err 117 A magnetic key is
stuck "on" for more
than 1 minute
Err 119 Multiple consecu-
tive invalid gas
readings occurred
Err 121 PIR LOCK ON with
relays set to ENGR
OFF.
Err 122 ICOM data error
Dräger Polytron
Remedy
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
according to specifications.
Remove power; check the
field wiring from the Poly-
tron 5x00 to the control
system; reapply power.
Remove power; reconnect
or replace sensor; reapply
power.
Remove power; reconnect
or replace sensor; reapply
power; if this persists, call
Dräger Service.
Calibrate sensor.
Calibrate sensor.
Perform zero calibration.
Check environment for
possible gases with nega-
tive cross-sensitivity to the
measured gas.
Have the instrument
checked by DrägerService.
Check 'diag scan'; refer to
PIR 7x00 Technical Hand-
book section "Faults,
Cause and Remedy" for
more information.
Configuration conflict for
proper safety operation.
Reconfigure relay ENGR
settings to resolve.
Sensor communications
error. Remove power;
reconnect or replace sen-
sor; reapply power; if this
error persists call Dräger
Service.
®
5000 Series
Fault Cause
number
Err 124 Beam Block error
Err 131 Cannot set PIR
lock
Err 198 Memory error
E198 Boot-load CRC
error
Err 199 Factory calibration
required

10.2 Warnings

Warning Cause
number
Info 300 Instrument set-
tings and sensor
settings are differ-
ent
Info 301 Sensor is warming
up
Info 302 Beam block warn-
ing
Troubleshooting en
Remedy
Clean optical surfaces; if
necessary, make sure that
hydrophobic filter, process
cuvette or process adapter
are correctly mounted.
Refer to PIR 7x00 Techni-
cal Handbook, section
"Check the Measuring
Cuvette of the Gas instru-
ment and Clean if
Required" and section
"Faults, Cause and Rem-
edy" for more information.
A1 and A2 settings and set
point are not identical. Cor-
rect relay settings before
engaging PIR LOCK.
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
Remedy
To select instrument set-
tings, tap [DOWN]. To
select sensor settings tap
[UP]. After selection is
made, display will show
'walking dashes'. When
data transfer is complete,
display will show 'CHk
CONF CAL'. Tap [OK] and
instrument will display
'walking dashes' then
return to normal operation.
Wait for warm-up phase to
end.
Clean optical surfaces; if
necessary, make sure that
hydrophobic filter, process
cuvette or process adapter
are correctly mounted.
Refer to PIR 7x00 Techni-
cal Handbook, section
"Check the Measuring
Cuvette of the Gas instru-
ment and Clean if
Required" and section
"Faults, Cause and Rem-
edy" for more information.