Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
7.10.2 – DEFROST
The machine evaporator is defrosted by stopping the compressor.
The machine evaporator is defrosted by stopping the compressor.
illumination of the wording
"dEF"
Automatic defrost can only take place during the holding period, at intervals of 8 hours with a duration of 10'.
defrost can only take place during the holding period, at intervals of 8 hours with a duration of 10'.
defrost can only take place during the holding period, at intervals of 8 hours with a duration of 10'.
Manual defrosting can be activated when the machine is on STANDBY and the evaporator temperature does not exceed +5° C, by
defrosting can be activated when the machine is on STANDBY and the evaporator temperature does not exceed +5° C, by
defrosting can be activated when the machine is on STANDBY and the evaporator temperature does not exceed +5° C, by
pressing
. Defrost ends at the end of 10' or when
. Defrost ends at the end of 10' or when
off forced ventilation takes place during Manual defrost, so it is advisable to keep the door open throughout the cycle.
ion takes place during Manual defrost, so it is advisable to keep the door open throughout the cycle.
ion takes place during Manual defrost, so it is advisable to keep the door open throughout the cycle.
7.10.3 – LONG IDLE PERIODS
Turn the machine OFF by pressing
Clean the machine thoroughly (see paragraph 8.2) and make sure the door is left open at the end of the operation and throughout the
Clean the machine thoroughly (see paragraph 8.2) and
idle period.
8 – MAINTENANCE
8.1 – SPECIAL PRECAUTIONS
Contact the manufacturer for any anomalies not described in this manual; contact the manufacturer also for any
Contact the manufacturer for any anomalies not described in this manual; contact the manufacturer also for any
Contact the manufacturer for any anomalies not described in this manual; contact the manufacturer also for any
doubts during the maintenance operations described herein.
doubts during the maintenance operations described herein.
doubts during the maintenance operations described herein.
personnel may damage the appliance and expose the operator to serious hazards. Maintenance carried out by
personnel may damage the appliance and expose the operator to serious hazards. Maintenance carried out by
personnel may damage the appliance and expose the operator to serious hazards. Maintenance carried out by
unauthorized personnel is considered tampering wi
unauthorized personnel is considered tampering with the appliance and therefore nulls the warranty and relieves
the manufacturer of any responsibility.
the manufacturer of any responsibility.
Any routine or extraordinary maintenance operation that requires the electric box to be opened or the
Any routine or extraordinary maintenance operation that requires the electric box to be opened or the
Any routine or extraordinary maintenance operation that requires the electric box to be opened or the
machine to be dismantled, even partially, must be carried out only after the appliance has been switched
machine to be dismantled, even partially, must be carried out only after the appliance has been switched
machine to be dismantled, even partially, must be carried out only after the appliance has been switched
off,
Any maintenance operations carried out on a live machine may cause people serious accidents which
may also be fatal.
The safety devices must be deactivated only by authorized personnel, who will guarantee safety for people and
The safety devices must be deactivated only by authorized personnel, who will guarantee safety for people and
The safety devices must be deactivated only by authorized personnel, who will guarantee safety for people and
avoid damage to the machine.
avoid damage to the machine.
maintenance.
During maintenance or repairs unauthorized persons must keep a safe distance from the appliance.
During maintenance or repairs unauthorized persons must keep a safe distance from the appliance.
During maintenance or repairs unauthorized persons must keep a safe distance from the appliance.
Observe the intervals prescribed or indicated in this manual for making insp
Observe the intervals prescribed or indicated in this manual for making inspections.
At the end of maintenance or repairs the appliance can be started only after the specialist engineer has made
At the end of maintenance or repairs the appliance can be started only after the specialist engineer has made
At the end of maintenance or repairs the appliance can be started only after the specialist engineer has made
sure that:
-
-
-
-
8.2 – ROUTINE MAINTENANCE
8.2.1 – ROUTINE MAINTENANCE TABLE (TAB. 5)
ROUTINE MAINTENANCE TABLE (TAB. 5)
Component
Type of operation
Chamber
Cleaning
External part
Cleaning
Condenser
Cleaning
Core probe
Cleaning
8.2.2 –CLEANING THE CHAMBER
Carry out this operation whenever necessary.
Carry out this operation whenever necessary.
APPLIANCE STATUS:
-
ON/OFF button on OFF (
-
power supply plug disconnected from the mains.
power supply plug disconnected from the mains.
AUTHORIZED PERSONNEL
Appliance operator.
METHOD
Clean very carefully the internal part of the chamber, the door closure surface (ref. 1 fig. 8) and
Clean very carefully the internal part of the chamber, the door closure surface (ref. 1 fig. 8) and gasket (ref. 2 fig. 8), using a non
abrasive sponge soaked in neutral detergent. Rinse with a sponge soaked in water and dry with a clean cloth.
abrasive sponge soaked in neutral detergent. Rinse with a sponge soaked in water and dry with a clean cloth.
abrasive sponge soaked in neutral detergent. Rinse with a sponge soaked in water and dry with a clean cloth.
Proper cleaning of the inside of the appliance prevents the formation of bad odour which could affect the end
Proper cleaning of the inside of the appliance prevents the formation of bad odour which could affect the end product negatively.
Proper cleaning of the inside of the appliance prevents the formation of bad odour which could affect the end
BCB_03-05-10-15 Rev.02
which starts flashing during the dripping stage.
which starts flashing during the dripping stage.
for three seconds, then unplug.
for three seconds, then unplug.
on the display, and unplugged.
display, and unplugged.
enance operations carried out on a live machine may cause people serious accidents which
enance operations carried out on a live machine may cause people serious accidents which
all the work has been fully carried out;
all the work has been fully carried out;
the safety systems are active;
the safety systems are active;
the appliance is working perfectly;
the appliance is working perfectly;
no-one is working
one is working on the appliance.
Timing
When needed
When needed
Every 30 days
Every cycle
on the display
on the display);
It can be Automatic or Manual and is shown on the display by
It can be
is pressed again. Because on STANDBY the compressor is already
is pressed again. Because on STANDBY the compressor is already
e the door is left open at the end of the operation and throughout the
th the appliance and therefore nulls the warranty and relieves
The safety devices must be carefully activated again after carrying out
The
safety devices must be carefully activated again after carrying out
Responsibility
Appliance operator
Appliance operator
Appliance operator
Appliance operator
and is shown on the display by
Maintenance carried out by unauthorized
Maintenance carried out by unauthorized
Maintenance carried out by unauthorized
gasket (ref. 2 fig. 8), using a non-
Method
See para. 8.2.2
See para. 8.2.3
See para. 8.2.4
See para. 8.2.5
Tab. 5
pag. 65
Publicité
Table des Matières
