Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
The cycle can be interrupted at any time by pressing
7.9.2 – SELECTING A TIME CONTROLLED FREEZING CYCLE
Load the machine suitably with the food to be chilled. If you wish to have greater temperature control, insert the core probe carefully
into the food: close the door.
With the appliance on STANDBY press
red (recommended chamber temperature during freezing). Press
icon flashes and
remains on.
temperature can be viewed at any time: when
seconds. In the same way, when
seconds.
After 90' (maximum time admitted for reducing the product temperature) the freezing cycle ends and the holding period
begins: the
icon goes on, the
display shows the chamber temperature in red.
Attention: the cycle can be interrupted at any time by pressing
beginning.
7.9.3 – SETTING A TEMPERATURE CONTROLLED FREEZING CYCLE
With the appliance on STANDBY press
the
and
icons will flash. Use
(recommended core temperature to end freezing). The
and
to edit this value: press
negative holding period). The
press
again to confirm the setting.
Press
(START) at any time to begin the cycle.
Attention: when selecting the cycle, if values different from the recommended ones are set they will not be saved and will be active only
until another cycle is selected or the machine is turned off.
7.9.4 – SETTING A TIME CONTROLLED FREEZING CYCLE
With the appliance on STANDBY press
the
and
icons will flash.
(maximum admitted time limit to end freezing). The
to edit this value: press
holding period).
The
to confirm the setting.
Press
(START) at any time to begin the cycle.
Attention: when selecting the cycle, if values different from the recommended ones are set they will not be saved and will be active only
until another cycle is selected or the machine is turned off.
7.10 –SPECIAL USES
7.10.1 – PRE-CHILLING FUNCTION
If the temperature of the food to be chilled is very high (above 65° C) it is advisable to pre-chill it in the following way: load the machine
with the food to be chilled, place the core probe in position (if you require a time controlled cycle assess whether to use the core probe
or not) and leave the door open.
With the appliance on STANDBY select the required cycle, then with the door open press
display the signal
"dOOr"
eliminate the heat through the open door.
moment you have one minute to close the door and let the machine complete the work cycle normally.
Attention: if you do not close the door within the time allowed when
continue. To reset a normal work cycle press
BCB_03-05-10-15 Rev.02
: the display will show the
The display will show the chamber temperature in red.
is pressed the display will show the temperature read by the probe, in green for 5
is pressed the display will show the minutes from the beginning of the cycle, in green for 5
icon flashes for a few seconds and the buzzer sounds. After that the
: the display will show
and
again to confirm the setting and view
icon now remains on and the
: the display will show
Use
and
to confirm the setting and view
icon now remains on and the
will flash and alternate with the measured temperature.
After a few minutes the display will show
(START) again.
(STOP): pressing
(START) again starts the cycle from the beginning.
and
(START) to begin the cycle. During the freezing stage the
(STOP): pressing
-40° C
(recommended chamber temperature during freezing) and
to edit this value: press
icon now remains on and the
-25° C
and
icons flash. Use
-40°C
(recommended chamber temperature during freezing) and
to edit this value: press
icon now remains on and the
-25° C
(recommended chamber temperature for the negative
and
icons flash.
"AL 1"
appears, the compressor will go off and ventilation only will
icons flashing and after three seconds
If the core probe is inserted the core
icon remains on and the
(START) again starts the cycle from the
again to confirm the setting and view
icon continues to flash.
(recommended chamber temperature for the
and
again to confirm the setting and view
icon continues to flash.
Use
and
to edit this value: press
(START) to begin the cycle. On the
In the chamber the fan will operate normally to
"AL 1"
and the buzzer will sound: from this
-40° C
in
-18°C
Use
to edit this value:
240'
Use
and
pag. 64
Publicité
Table des Matières
