Maintenance; Storage; 11: Electrical Connection - Scheppach DECO-XL Traduction Du Manuel D'origine

work bench.
• Install the saw blade through the hole in the work
piece and through the work blade slot, and fasten
the blade to the holders.
• When you have completed the inside cut, remove
the saw blade and then remove the workpiece from
the bench.
Foot switch / continuous operation (Fig. 1+12+13)
The machine can be operated in continuous opera-
tion or with the additional foot switch (9). The switch
(11) is used to select between the operating modes.
The operating mode should always be selected when
the machine is switched off.
The machine is in the foot switch mode when the
switch is at the "0" position.
The machine is in the continuous mode when the
switch is at the "I" position.
Attention! The machine may start due to unintentional
actuation of the foot switch in the foot switch mode.
Attention! Never leave the machine unattended while
it is switched on.
Switching on/off (Fig. 1+12)
It is possible to switch the saw on by pressing the
green "I" button (6).
In order to switch the saw off again, it is necessary to
press the red "0" button (6).
The red warning light (a) indicates whether the machine
is switched on or off. The machine is switched on when
this lights up. (The machine only starts up in the foot
switch mode once the pedal is actuated, the red warn-
ing light illuminates anyway.)
You can only switch between foot switch and continu-
ous operation when the red warning light is not illumi-
nated. If necessary, switch machine off first by pressing
the red button "0" (6).
Make sure you are aware of what operating mode
(pedal/continuous operation) your machine is in before
switching it on.
Beware of unintentional actuation of the foot switch.
Set the pedal (9) on the ground. The machine can be
switched on/off in pedal mode when the pedal is actu-
ated. A foot switch for switching on/off is practical, espe-
cially for internal cuttings, since your hands are kept free
and you can fully concentrate on the work piece under
the scroll saw. However, it cannot influence the speed.
With the continuously variable electronic speed control
(5), the cutting speed can be increased by turning to the
right or reduced by turning to the left.
Lighting system (8) (Fig.1+14)
The lighting system can be switched on by pressing the
switch (b) on the lamp.
The lighting system is switched off if the switch is
pressed again.
To change the batteries (2x AAA R03 1.5), open the
battery compartment on the bottom of the light by re-
moving the three screws (c) using a Phillips screwdriver.
Insert the new batteries. Dispose of the old batteries
properly.
Fit the cover of the battery compartment in reverse or-
der.

9. Maintenance

Warning: In the interests of operational safety, al-
ways switch off the saw and remove the mains plug
before carrying out maintenance work.
General
Wipe chips and dust off the machine from time to time
using a cloth.
Re-application of the wax coating on the workbench
makes feeding the workpiece to the blade easier.
Motor
The mains cable should be replaced immediately if
pulled out, cut or damaged in any other way.
Do not lubricate the motor bearings or internal parts!
Saw arm bearings
Lubricate the saw arm bearings every 50 hours. Pro-
ceed as follows (Fig. 15).
• Turn the saw to the side
• Apply a generous amount of SAE 20 oil to the shaft
end and bronze bearings.
• Let the lubricant oil work in overnight.
• Repeat the procedure the next day on the other
side of the saw.
There are no parts inside the equipment which re-
quire additional maintenance.
Special accessories
Pin saw blade-universal
135 x 2,0 x 0,25 Z 10
blade mm 1 set = 6 pieces,
Pin saw blade- wood/plastic mm
135 x 2,0 x 0,25 Z 7
1 set = 6 pieces,
Pin saw blade-wood mm
135 x 3,0 x 0,5 Z 4
1 set = 6 pieces,

10. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag-
ing.
11. Electrical connection
The installed electric motor is completely wired ready
for operation.
The customer's connection to the power supply sys-
tem, and any extension cables that may be used,
must conform with local regulations.
Important remark:
The motor is automatically switched off in the event
of an overload. The motor can be switched on again
after a cooling down period that can vary.
Article No. 8800 0011
Article No. 8800 0012
Article No. 8800 0013
GB 21