Air Supply Cartridge Installation; Unloading Your Marker And Air Supply Cartridge Removal - Tippmann TPX Marker Manuel D'utilisation

Unloading Your Marker and Air Supply Cartridge Removal

Do not store or disassemble a marker with the air supply cartridge ( punctured
E
or unpunctured ) installed. ❏ If your marker has the optional remote line
adaptor kit installed, do not remove the air supply cartridge until you first
N
follow the air supply cylinder removal instructions in the Optional Remote
G
Line Adaptor instructions ( see page 21).
L READ EACH STEP COMPLETELY BEFORE PERFORMING THE STEP:
❏ Eye protection designed for paintball use must be worn by the user and
I
any person within range.
S
WARNING
H
KEEP EXPOSED SKIN AWAY FROM ESCAPING
GAS ( ) WHEN INSTALLING OR REMOVING
AIR SUPPLY CARTRIDGE OR IF THE MARKER
OR AIR SUPPLY IS LEAKING.
COMPRESSED AIR, CO2, AND NITROGEN
GASSES ARE VERY COLD AND CAN CAUSE
FROSTBITE UNDER CERTAIN CONDITIONS.
To unload a marker with an UN-PUNCTURED air
cartridge (non-used):
1) Put the safety
in the SAFE mode (see page 4) and
install the barrel blocking device
2) Remove the magazine
button and the magazine will eject out. NOTE: when
removing a loaded magazine from the marker, 2 loose
balls might drop from the grip. Push the magazine tab
down until it locks to take pressure off the balls and
reload any balls into the magazine.
3) Remove the CO compartment cap
2
and keep marker pointed in a safe direction during CO
compartment cap removal.
Step 1. Push in and turn the CO
until it stops. Then pull out until it stops to partially un-
screw the cap. NOTE: The cap should be easy to turn
- If you are unable to turn it or if it is difficult to turn, the
cartridge has been punctured and you must follow the
instructions To Unload a marker with a PUNCTURED
air supply cartridge (see page 13).
Step 2. Turn the CO cap
2
clockwise until it stops and pull it out, the cartridge will
then slide out
(see page 2).
. Press the magazine release
in two steps
2
cap counterclockwise
2
a second turn counter-
.
UN-PUNCTURED air Cartridge Removal
12
(continued on page 13)
UN-PUNCTURED air Cartridge Removal (continued from page 12)
❏
4) Replace the CO
pin guides of the cartridge compartment and push the cap in
clockwise. Push the cap in
Put the trigger safety
blocking device
To unload a marker with a PUNCTURED air cartridge (used): NOTE:
a punctured / used air supply cartridge must be emptied of all air before
removal.
1) Put the safety
blocking device
2) Remove the magazine
the magazine will eject out. NOTE: When removing a loaded magazine from
the marker, two loose balls might drop from the grip. Push the magazine
tab down until it locks to take pressure off the balls and reload the
paintballs into the magazine.
3) Go to a designated firing area and remove the barrel blocking device.
4) Point the marker in a safe direction, turn off the safety and fire until there
is no air left in the cartridge. NOTE: If you have a punctured cartridge in
your marker and the marker will not fire: follow the instructions on page
19 - To Release Pressure From a Marker that Will Not Fire.
5) Put the safety
blocking device (see page 2).
6) Visually inspect the chamber for paintballs through the opening at the
bottom of the grip for the magazine.
7) Remove the CO
a safe direction during CO
exposed skin away from escaping gas - the arrows ( ) in the WARNING
illustration on page 12 show gas escape points. Push in and turn the CO
cap slowly counterclockwise until it stops and pull until it stops to partially
unscrew the cap, then wait as any remaining air in the cartridge escapes
before performing step 2 (keep exposed skin away from escaping air).
Step 2. Turn the CO
and pull it out, the cartridge will slide out
8) Replace the CO
pin guides of the cartridge compartment and push the cap in
clockwise. Push the cap in
Put the trigger safety
blocking device (see page 2).
compartment cap . Align the cap pins with the
2
a second time and turn clockwise.
in SAFE mode (see page 4) and install the barrel
(see page 2).
in the SAFE mode (see page 4) and install the barrel
(see page 2).
. Press the magazine release button
in the SAFE mode (see page 4) and install the barrel
cap in two steps and keep marker pointed in
2
compartment cap removal. Step 1. Keep
2
cap a second turn counterclockwise until it stops
2
compartment cap : Align the cap pins with the
2
a second time, turn clockwise and release.
in safe mode (see page 4) and install the barrel
13
and turn
E
N
G
L
I
S
H
and
2
.
and turn