Page 16 Firing Valve; Air Valve; Regulator; Regulator Pressure Relief Valve Adjustment - Tippmann TPX Marker Manuel D'utilisation

Marker Disassembly / Assembly (continued from page 17)
2) Slide the ❏ front bolt spring
the power tube .
E
3) Remove power tube from the air valve body: ❏ hold air valve body
and unscrew the power tube with a 1/2" wrench on "wrench flats"
N
4) To access the air valve body
G
a snap ring tool. (NOTE: the snap ring tool tip should fit snuggly into the snap
ring - using a snap ring tool with tips too small may cause the snap ring to fly
L
off the tool and cause injury and/or damaged parts.) To remove the internals
I
from the air valve body , carefully push them out with a plastic tool as
shown.
S
H
5) Clean and inspect parts. Replace any damaged
parts. (NOTE: O-rings are shown removed: It is not
necessary to remove O-rings as shown to inspect,
clean, and lubricate.) Use Tippmann
lightly lubricate the O-rings
/ and springs / to maintain your marker in good working condition.
6) To reassemble, follow these instructions in reverse. NOTE: Carefully hand
start all threaded parts and do not overtighten and strip threaded parts when
reassembling. NOTE: Failure to reassemble correctly can cause damage to
parts, air leaks, and other problems. As you reassemble your marker, double
check to be sure parts are clean, not damaged, lubricated and installed correctly.
Regulator Disassembly / Assembly
1) Follow Marker Disassembly / Assembly - on page 15. Remove air fitting
2) Remove the Regulator End Cap
the regulator body on the "wrench flats"
end cap (turning to the left with a 3/16" allen wrench). Parts will then slide out.
3) To remove the velocity adjustor
and the spring come out. Use your fingers to pull the regulator piston
4) Clean and inspect parts.
Replace any damaged
parts. (NOTE: It is not
necessary to remove O-rings to to inspect, clean, and lubricate them.) Use
Tippmann grease to lightly lubricate O-rings
®
your marker in good working condition.
5) Reassemble the regulator following these instructions in reverse. NOTE:
Failure to reassemble correctly can cause damage to parts, air leaks, and other
problems. As you reassemble your marker, double check to be sure parts are
clean, not damaged, lubricated and installed correctly.
6) Upon marker reassembly-you will need to adjust the Regulator Pressure
Relief Valve (see Regulator Pressure Relief Valve Adjustment on page 19).
; ❏ front bolt and ❏ damper
internals: ❏ remove the snap ring
NOTE: The Firing Valve
Assembly
to the Air Valve
® grease to

page 16 Firing Valve

Disassembly/Assembly).
from the regulator body by holding
with a 5/8" wrench, and remove the
, unscrew it with a 3/16" allen wrench until it
and springs / to maintain
18
off
KEEP EXPOSED SKIN AWAY FROM ESCAPING GAS WHEN INSTALLING OR
.
REMOVING AIR SUPPLY CARTRIDGE OR IF THE MARKER OR AIR SUPPLY
with
IS LEAKING. COMPRESSED AIR, CO2, AND NITROGEN GASSES ARE VERY
COLD AND CAN CAUSE FROSTBITE UNDER CERTAIN CONDITIONS.
To Release Pressure From a Marker that Will Not Fire:
Only use this procedure if marker will not fire and the CO
been punctured. Put the safety in the Safe Mode (see page 4), remove the
magazine as outlined in Unloading Your Marker and Air Supply Cartridge
Removal (see page 12) and install the Barrel Blocking Device (see page 2).
Keep marker pointed in a safe direction during CO
Keep exposed skin away from escaping gas
as it rushes out at the air release points ( ).
attaches
Remove exterior locking set screw, and
(see
then slowly loosen adjusting set screw
t o e m p t y C O
Remove and dispose of the CO
complete cartridge removal as outlined on page 12. See Adjustable CO
Cartridge Cap on page 25 for further information.

Regulator Pressure Relief Valve Adjustment:

The regulator pressure relief valve is factory set to 350 psi. Do not reset it
higher than 350 psi which could cause damage to marker parts or cause
personal injury. If you disassemble the Regulator (see page 18) - you will
need to reset the regulator pressure relief valve before using your marker.
.
❏ Put the safety in the Safe Mode (see page 4), remove the magazine as
outlined in Unloading Your Marker and Air Supply Cartridge Removal (see
page 12) and install the Barrel blocking Device (see page 2).
1) ❏ Adjust the velocity as outlined in Velocity Adjustment on page 8 until
your marker chronographs out at 300 fps.
out.
2) ❏ Insert a 1/8" wrench
adjustor set screw
screw and turn it slowly to the left
begins to escape through the relief valve
turn the screw slowly back to the right
air stops escaping to set the relief pressure. NOTE:
do not turn any further to the right which would
reset it higher than 350 psi. This could cause damage
to marker parts or cause personal injury.
3) ❏ Follow the Velocity Adjustment Instructions on
page 8 to adjust the velocity down until the marker
chronographs to 300 fps or less.
WARNING
f r o m t h e c a r t r i d g e .
2
cartridge. With pressure released -
2
through the velocity
and into the regulator relief set
only until air
. Then
only until
19
E
N
G
L
cartridge has I
2
S
H
cap removal.
2
2