Tippmann TPX Marker Manuel D'utilisation page 10

Marker Disassembly / Assembly (continued from page 15)
To separate assembly :
❏ Pull the long gas line
E
fittings . (At reassembly lubricate the long
gas line O-rings).
N
❏ Pull the regulator from the air valve
G
line (lubricate O-rings at reassembly). ❏ Remove firing valve
L air valve ( see Firing Valve disassembly below on page 16).
5) ❏ Lift out the: ❏ magazine
I
release and release spring
S
❏ safety (at reassembly the
black O-ring end goes into right re-
H
ceiver half); ❏ trigger ; ❏ trigger
pin (long) ; ❏ ball latch
breech window ; ❏ release actua-
tor ; and ❏ the actuator link
6) ❏ Clean and ❏ inspect parts.
❏ Replace any damaged parts. Use
Tippmann grease to lightly lubricate
®
the O-rings ; spring and pins
/ to maintain your marker in
good working condition.
7) To reassemble, ❏ follow these instructions in reverse and be
sure pin is pushed in flush to the firing valve body as shown.
NOTE: Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when reassembling. NOTE: Failure to reassemble
correctly can cause damage to parts, air leaks, and other problems. As
you reassemble your marker, double check to be sure parts are clean, not
damaged, lubricated and installed correctly.
Firing Valve Disassembly / Assembly
1) Follow ❏ Marker Disassembly / Assembly - on page 15.
2) Remove the firing valve
valve ,❏ remove the 2 bolts
the left with a 3/32" allen wrench
3) The 2 O-rings are not attached.
NOTE: ❏ Be sure the 2 O-rings
place when reassembling the firing valve
to the air valve with bolts
4) ❏ Pull pin out. NOTE: ❏ When
reassembling be sure pin
in flush to the firing valve body as shown.
5) ❏ Remove screw turn to left
out of the two air
and ❏ pull out the short gas
;
Black O-ring
Red
; ❏
.
from the air
turn to
.
are in
.
is pushed
with a 3/32" wrench
Marker Disassembly / Assembly
16
(continued on page 17)
Marker Disassembly / Assembly (continued from page 16)
6) ❏ Tap the firing valve body
should fall out ( if you need to pull the parts out - use a plastic tool so
you do not damage the parts).
7) ❏ Clean and ❏ inspect parts. ❏ Replace any damaged parts. Use
Tippmann grease to lightly lubricate the spring
®
from
to maintain your marker in good working condition.
8) To reassemble and attach the firing valve
low these instructions in reverse. NOTE: Carefully hand start all threaded
parts and do not overtighten and strip threaded parts when reassembling.
NOTE: Failure to reassemble correctly can cause damage to parts, air
leaks, and other problems. As you reassemble your marker, double check
to be sure parts are clean, not damaged, lubricated and installed correctly.
Puncture Valve Disassembly / Assembly
1) Follow ❏ Marker Disassembly / Assembly on page 15.
❏ Unscrew
reassembling).
2) To access the puncture valve internals: ❏ remove the snap ring
with a snap ring tool (NOTE: the snap ring tool tip should fit snuggly
into the snap ring - using a snap ring tool with tips too small may cause
the snap ring to fly off the tool and cause injury and/or damaged parts.)
❏ To remove the internals from the puncture valve body
puncture pin cap
parts out as shown
3) ❏ Clean and ❏ inspect parts. ❏ Replace any damaged parts.
(NOTE: O-rings are shown removed: It is not necessary to remove O-
rings as shown to inspect, clean and lubricate.) Use Tippmann
lightly lubricate the O-rings
in good working condition.
4) To reassemble, ❏ follow these instructions in reverse. NOTE: Carefully
hand start all threaded parts and do not overtighten and strip threaded
parts when reassembling. NOTE: Failure to reassemble correctly can
cause damage to parts, air leaks, and other problems. As you reassemble
your marker, double check to be sure parts are clean, not damaged,
lubricated and installed correctly.
Air Valve Disassembly / Assembly
.
1) Follow Marker Disassembly / Assembly - on page 15.
and 2 O-rings
air fitting (do not overtighten and strip threads when
and carefully push puncture pin
.
and springs to maintain your marker
17
and the valve bushing
E
N
, O-rings and
G
L
to the air valve , fol-
I
S
H
, remove the
and internal
grease to
®
Marker Disassembly / Assembly
(continued on page 18)