Painting - Titan PowrLiner 550 Mode D'emploi

Operation
10. Turn the relief valve knob to the SPRAY (
11. Unlock the gun by turning the gun trigger lock to the
unlocked position.
12. Fully pull the spray lever on the cart handle to rev the
engine, pressurize the sprayer, and trigger the spray
gun. Fluid will begin flowing through the spray hose
and out of the gun.
13. Continue to pull the spray lever on the cart handle until
the old solvent/test fluid is gone and fresh solvent is
coming out of the gun.
14. Release the spray lever.
15. Lock the gun by turning the gun trigger lock to the
locked position. If necessary, loosen the gun holder
clamp knob and then engage the spray gun trigger lock.
Move the spray gun to its original position and tighten
the clamp knob.
16. Check the entire system for leaks. If leaks occur,
turn the sprayer off and follow the "Pressure Relief
Procedure" in this manual before tightening any fittings
or hoses.
17. Follow the "Pressure Relief Procedure" (section 4.5) in
this manual before changing from solvent to paint.
Be sure to follow the Pressure Relief Procedure
when shutting the unit down for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips,
or preparing for cleanup.
GB
p
4.3
) position.
1. Place a five gallon bucket of material between the
i
2. Place the siphon hose into a container of paint.
3. Place the bleed hose into a metal waste container.
4. Turn the relief valve knob to the PRIME (
5. Fully depress the pusher stem to make sure the inlet
6. Start the engine:
a. Move the choke lever (1) up to the full choke position.
b. Push the rubber prime button (2) 7-10 times.
c. Pull the starter rope (3) rapidly and firmly. Continue to hold
d. Once the engine is running, slowly move the choke lever (1)
7. Fluid will begin flowing through the return hose and
8. Turn off the sprayer by pressing and holding the engine
9. Remove the bleed hose from the waste container and
10. Start the engine.
11. Turn the relief valve knob to the SPRAY (
12. Unlock the gun by turning the gun trigger lock to the
13. Fully pull the spray lever on the cart handle to rev the
14. Continue to pull the spray lever on the cart handle until
15. Release the spray lever.
16. Lock the gun by turning the gun trigger lock to the
17. Turn the relief valve knob to the PRIME (
18. Turn off the sprayer by pressing and holding the engine
19. Attach tip guard and tip to the spray gun. Refer to the
12

Painting

bucket holders on the cart. Make sure the bucket
holders hold the five gallon bucket securely. Adjust
the bucket holders using the thumb screw located
underneath each holder, if necessary.
When using this line striper for first time, it
may be helpful to use water in place of paint to
gain familiarity with the operation of the line
striper. After changing from water to paint,
test spray several lines on cardboard, roofing
felt, or rosin paper before striping to ensure
correct line width.
ball is free.
the rope as you let it return. Pull and return the rope until
the engine starts.
down to the closed position
into the waste container. Allow the sprayer to run for
15–30 seconds to flush the test fluid out through the
return hose and into the waste container.
shutoff switch until the motor shuts off.
place it into the container of paint.
unlocked position.
engine, pressurize the sprayer, and trigger the spray
gun. Fluid will begin flowing through the spray hose
and out of the gun.
material is coming out of the gun.
locked position. If necessary, loosen the gun holder
clamp knob and then engage the spray gun trigger lock.
Move the spray gun to its original position and tighten
the clamp knob.
shutoff switch until the motor shuts off.
instructions in section 4.4.
k
) position.
p
) position.
k
) position.
PowrLiner 550