Scheppach 5904806903 Traduction Du Manuel D'origine page 40

Notice. Below the angle and dimensions If the chain is
not properly sharpened or the depth is too small, there
is a higher risk of reversion effects and resulting inju-
ries! The chain cannot be fixed on the guide rail. It is
therefore best to remove the chain from the rail and
then sharpen.
• Select the appropriate tools for the chain pitch sharp-
ening tool. See "Specifications" for the allowed chain
pitches.
The chain pitch (for example 3/8 ") is highlighted in the
depth of each blade.
Use only special files for chainsaws! Other files have the
wrong shape and the wrong cut.
Select the file according to the diameter of your chain
pitch. Make sure to observe the following angle when
sharpening the chain diameter.
A = filing angle
B = the angle of the side plate
The angle must also be maintained for all knives.
For irregular angles, the chain is run irregularly, wear quick-
ly and break down prematurely.
Since these requirements can only be met with sufficient
and regular exercise:
• A File Holder must be used when sharpening the saw
chain by hand. The correct filing angle marked on it.
• Hold the file horizontally (at a right angle to the guide rail)
and file according to the angle mark on the file holder.
Support the file holder on the top plate and depth gauge.
• File down. The knife is always from the inside to the out-
side
• The file sharpens only in forward motion. Lift it off in the
backward motion.
• Do not touch the dynamic links with the file.
• Turn the file regularly continue to avoid a onesided wear.
• Remove to remove a piece of hard wood, bones raw
edges.
All knives must have the same length, otherwise they will
also vary. As a result, the chain is irregular and it increases
the risk of going broke.
Oiling the gears (pole saw)
Oil the gears every 10 to 20 operating hours.
1 Position the grease gun at the lubricating nipples
Fig.54(Q).
2 Insert some grease.
Attention! Fill only a small amount of grease. Do not
overfill.
Check the hedge trimmer for obvious faults such as:
– loose attachments
– worn or damaged components
40 GB
– bent, broken or damaged cutting tools
– correctly attached and working covers and safety de-
vices
– wear, in particular, cutting tool play
Immediately replace damaged or blunt cutting tools,
even in the event of minor damage.
Oiling the gears (hedge trimmer)
Oil the gears every 10 to 20 operating hours.
1 Position the grease gun at the lubricating nipples
Fig.48(P).
2 Insert some grease.
Attention! Fill only a small amount of grease. Do not
overfill.
Oil the cutting tools and the angle adjustment with envi-
ronmentally friendly lubricant.
Adjusting the idle speed Fig. 62
If the cutting device runs idle, correct the idle speed.
1. Allow the engine to warm for 3-5 minutes
(No high speeds!).
2. Turn the adjusting screw (S): clockwise
- idle speed increases (+)
counterclockwise
- Idling speed decreases (-)
The idle speed is 3000 min-1
Contact the manufacturer if the cutter continues to run
at idle.
Do not continue to operate the unit!
The user is responsible for all damages caused by
non-compliance with instructions in this manual.
This also applies to non-authorized modifications of
the tool, use of non-authorized spare parts, acces-
sories, working tools, unrelated and not intended
use, secondary damages due to use of faulty com-
ponents.
Wear Parts
Even when used in the intended way, some components are
subject to normal wear. They have to be replaced depending
on the kind of duration of usage. These parts include, among
others, the cutting tool and the retaining disk.
m Warning! Use only original manufacturer's replace-
ment parts, accessories and attachments. Failure to do
so can cause poor performance, possible injury and may
void your warranty
Important hint in case of sending the equipment to a
service station:
Due to security reasons please see to it that the equip-
ment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering replace-
ment
parts:
• Type of machine
• Article number of the machine