Publicité
Les langues disponibles
Les langues disponibles
OPERATION
■
Always stop the engine, disconnect the spark plug cap
from the spark plug, allow it to cool, and make sure all
moving parts have come to a complete stop before:
●
refuelling
●
adjusting the working position or the rear handle
position
●
leaving the product unattended
●
cleaning the product
●
changing the accessories
●
clearing blockages
●
checking for any damage after hitting an object
●
checking for any damage if the product starts to
vibrate abnormally
●
performing maintenance
■
Only start the engine when the hedge trimmer is in a
safe working position. The manufacturer recommends
that the product is placed on the ground where the
blades cannot contact anything before you start the
engine.
■
While operating the hedge trimmer, do not overreach
or stand on unstable support. Keep proper footing
and balance at all times. The manufacturer does not
recommend the use of steps or ladders. If higher
trimming is required, use an extended reach tool.
■
Do not operate the product with a damaged or
excessively-worn cutting device.
■
To reduce fire hazard, keep the engine and the silencer
free of debris, leaves, or excessive lubricant.
■
Always ensure that all handles and guards are fitted
when using the hedge trimmer. Never attempt to use
an incomplete hedge trimmer or one fitted with an
unauthorised modification.
■
Always use two hands to operate the hedge trimmer
which is fitted with two handles.
■
Familiarise yourself with your surroundings and be on
the alert for possible hazards which you may not notice
because of the noise from the hedge trimmer.
ADDITIONAL WARNINGS
■
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect. Carbon
monoxide is a colourless, odourless, and an extremely
dangerous gas which can cause unconsciousness or
death.
■
Do not use the hedge trimmer when you are tired, ill,
or under the influence of alcohol, drugs, or medication.
■
Ensure before each use that all controls and safety
devices function correctly. Do not use the product if
the "off" switch does not stop the engine. The defective
switch must be replaced by an authorised service
centre.
■
Inspect the hedge trimmer before each use. Check for
fuel leaks or loose fasteners, etc. Do not operate if fuel
is leaking or handles and guards are not secure and
fully functional.
■
Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
2
| English
■
Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
■
Check the work area before each use. Remove all
foreign objects such as posts, wire, or string which may
damage or become entangled in moving parts or cutting
means.
■
Check constantly for persons or animals behind or
inside any hedge or bush to be trimmed. Operating
similar tools nearby increases both the risk of hearing
injury and the potential for other persons to enter your
working area.
■
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre before use.
WARNING
When the throttle trigger is released and the engine is
running at idle speed, the cutting attachment or blade
must not move. If it does continue to move, there is risk
of severe injury to the operator. Do not use the product.
Bring it to an authorised service centre for professional
adjustment.
■
Do not touch the area around the silencer or engine of
the product, these parts get very hot during operation.
■
Do not modify the product in any way
■
Do not force the hedge trimmer through heavy
shrubbery. This can cause the blades to bind and slow
down. If the blades slow down, reduce the pace.
■
Do not attempt to cut stems or twigs that are larger
than 28 mm thick, or those obviously too large to feed
into the cutting blade. Use a non-powered hand saw or
pruning saw to trim large stems.
■
Ensure to keep a running or hot engine and silencer
well away from combustible materials to reduce the risk
of fire.
TRANSPORTATION AND STORAGE
■
Stop the engine and allow it to cool before storing or
transporting.
■
Clean all foreign material from the product.
■
Cover the blade with the blade protector (scabbard).
■
Drain all fuel from the tank into a container approved
for petrol. Remember to properly replace and tighten
the fuel cap.
■
Run the engine until it stops. This will remove all fuel
that could become stale and leave varnish and gum in
the fuel system.
■
Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children and well away from
sources of ignition.
■
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■
Do not store outdoors.
■
When transporting the product in a vehicle, secure it
against movement or falling to prevent injury to persons
Publicité
