EINHELL TE-AC 400/50/10 V Instructions D'origine page 18

•
Nut for fitting the axle (2x)
•
Axle screw (2x)
•
Original operating instructions
•
Safety information
3. Proper use
The compressor is designed for generating
compressed air for tools operated by compressed
air.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Mains connection: ................... 220-240 V ~ 50 Hz
Motor rating: ............................................. 2200 W
Speed (motor) min-1: ................................... 2850
Speed (pump) min-1: ................................... 2850
Operating pressure bar: ........................... max. 10
Pressure vessel capacity (in liters): ................. 50
Theoretical suction rate l/min ........................ 400
Output (compressed air) at 7 bar: . . 155 liters/min
Output (compressed air) at 4 bar: ... 210 liters/min
Sound power level L
WA
K uncertainty: ........................................ 2.04 dB
WA
Sound pressure level L
K uncertainty: ........................................ 2.04 dB
pA
Protection type: ............................................. IP20
Weight of the unit in kg: .................. approx. 43 kg
Oil quantity: .............................. approx. 0.19 liters
Noise
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Anl_TE_AC_400_50_10_V_SPK9.indb 18 Anl_TE_AC_400_50_10_V_SPK9.indb 18
in dB: ............................ 96
in dB: ....................... 76
pA
- 18 -
GB
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Examine the machine for signs of transit da-
mage. Report any damage immediately to the
company which delivered the compressor.
•
The compressor should be set up near the
working consumer.
•
Avoid long air lines and long supply lines (ex-
tensions).
•
Make sure the intake air is dry and dust-free.
•
Do not set up the compressor in damp or wet
rooms.
•
The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from +5°C to +40°C). There must
be no dust, acids, vapors, explosive gases or
inflammable gases in the room.
•
The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor
in areas where work is conducted with spray-
ed water.
•
The oil level in the compressor pump has to
be checked before putting the equipment into
operation.
•
The equipment must be set up where it can
stand securely.
•
Use flexible hoses in order to prevent trans-
mitting unacceptable loads to the pipeline
system at the connection between the com-
pressor system and the pipeline system.
•
It is essential to use separators, traps and
drains which process the liquids produced by
the compressor before the compressor sys-
tem is put into operation.
•
Supply hoses at pressures above 7 bar
should be equipped with a safety cable (e.g.
a wire rope).
6. Assembly and starting
Notice!
You must fully assemble the appliance before
using it for the fi rst time.
6.1 Fitting the wheels (3)
Fit the supplied wheels as shown in Fig. 5.
26.01.2018 06:29:15 26.01.2018 06:29:15