Bosch EPS 118 Notice Originale page 87

Assembly
1. Slide the new filter element (Fig. 47, item 5) onto
the deflector (Fig. 47, item 6).
2. Secure the deflector plate (Fig. 47, item 4).
3. Before installing the filter assembly, check if the
O-ring (Fig. 47, item 7) is present and correctly
installed on the condensate vessel.
4. Insert the filter assembly (Fig. 47, item 3) into the
condensate vessel and turn it by 45° to secure it.
5. Before installing the condensate vessel, check if
the O-ring (Fig. 47, item 8) is present and correctly
installed on the deflector.
i
On the condensate vessel, there are two lines
(Fig. 48, item 1,2) to the left and right of the
lock. While the condensate vessel is inserted
into the maintenance unit, one of the lines must
align with the indentation (Fig. 48, item 3) on
the maintenance unit. Then, turn the condensate
vessel in the direction of the indentation until
the lock engages audibly.
1
Fig. 48: Condensate vessel installation position
6. Secure the condensate vessel (Fig. 47, item 1) on
the maintenance unit (Fig. 47, item 9).
7. Connect the compressed-air line to the mainte-
nance unit.
8. Switch on the compressed air.
9. Check for leakage. In case of leakage, check instal-
lation position of the condensate vessel.
10. Check if the condensate hose is still properly run
into the collecting container.
Robert Bosch GmbH
3
2
Maintenance | EPS 118 | 87
8.3 Spare and wearing parts
Designation
Maintenance package with:
R 100 x strainer
<)
R 10 x o-ring 7.66 x 1.78
<)
R 1 x air filter for maintenance unit
R 1 x test oil filter
<)
Degassing adapter
<)
Sealing plug for leak check
<)
Connection adapter
<)
High-pressure hose assembly
Hose assembly (return)
<)
Bosch Piezo CRI hose assembly (return)
Adapter cable for Bosch CRI/piezo CRI
Adapter cable for CRIN
<)
Bosch CRI hose fitting with O-ring
Bosch CRI 2.5 hose fitting with O-ring
Bosch CRIN hose fitting
<)
CRIN adapter with check valve for Bosch in-
jectors
<)
Inlet connector
<)
12 x O-rings 9.5 x 2 for inlet connector
Adapter M12 — M14
<)
O-rings for injection chamber
R 20 x O-rings 7 mm
<)
R 20 x O-rings 9 mm
<)
O-rings for injection chamber
R 20 x O-rings 60.05 mm
<)
R 20 x O-rings 69.57 mm
<)
Clamping bush (17 mm)
<)
Clamping bush (19 mm)
<)
Clamping bush (21 mm)
<)
WLAN-USB-Adapter
High-pressure pump control valve
Wearing parts
<)
Customer service performs maintenance and exchanges.
1)
i
Parts that are subject to wear from use or other na-
tural causes of wear or must be exchanged during
maintenance are not covered by the guarantee.
en
Order number
1 687 010 576
<)
1 683 457 129
1 683 080 012
1 681 032 120
1 680 712 389
<)
1 684 462 570
1 684 462 569
<)
1 684 463 952
<)
1 684 463 953
1 681 334 034
<)
1 681 032 119
<)
1 683 386 192
1 683 350 904
1 683 386 166
1 680 210 143
<)
1 681 321 362
1 687 010 519
1 687 010 520
1 681 091 184
1 681 091 185
1 681 091 186
1 687 010 561
–
<) 1)
|
1 689 989 300 2020-03-24
1)