Operation - EINHELL TE-SM 36/210 Li - Solo Instructions D'origine

relation to the saw blade (7) and retighten the
adjustment screws (12).
•
The angle stop (a) and hex key (4 mm) are
not included in the scope of this delivery -
they are available from your dealer.
5.5 Precision adjustment of the stop for cros-
scut 90° (Figs. 1, 12, 13)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking lever (21) and move the ma-
chine head (4) all the way to the right using
the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Adjust the adjustment screw (29) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Finally, check the position of the pointer (20)
on the scale (19). If the pointer (20) still does
not show the correct angle on the scale, it can
be readjusted.
•
To readjust it, undo the fastening screw on
the pointer (20) using a screwdriver. Move the
pointer to the desired scale position and then
retighten the fastening screw.
•
The angle stop (a) and hex key (4 mm) are
not included in the scope of this delivery –
they are available from your dealer.
5.6 Precision adjustment of the stop for miter
cuts 45° (Figs. 1, 12, 14)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking lever (21) and move the ma-
chine head (4) all the way to the left using the
handle (1), until it coincides at 45°.
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
The angle stop (b) and hex key (4 mm) are
not included in the scope of this delivery –
they are available from your dealer.

6. Operation

6.1 Charging the lithium-ion battery pack
(Figs. 15, 16, 23)
1. Remove the rechargeable battery (39) from
the mount (40) by pressing the pushlock
button on the battery and pulling it out of the
mount.
2. Check that your mains voltage is the same as
Anl_TE_SM_36_210_Li_Solo_SPK9.indb 32
GB
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(41) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Adjusting the movable stop rail
(Figs. 17-20)
Warning! To make 90° crosscuts, the adjustable
stop rail (37) must be fi xed at the inner position:
•
Undo the locking screw (38) of the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (37) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (37) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
- 32 -
12.08.2020 10:51:05