Technical Data; Before Starting The Equipment - EINHELL TE-SM 36/210 Li - Solo Instructions D'origine

4. Technical data

Motor power supply ................................36 V d.c.
Idle speed n : ....................................... 3800 rpm
0
Carbide saw blade: ...........ø 210 x ø 30 x 1.8 mm
Number of teeth: ............................................ 40
Swiveling range: .......................... -47° / 0° / +47°
Miter cut to the left: .................................0° to 45°
Saw width at 90°: ............................ 310 x 65 mm
Saw width at 45°: ............................ 210 x 65 mm
Saw width at 2 x 45°
(double miter cut, left): .................... 210 x 35 mm
Max. cutting height: .................................. 65 mm
Max. workpiece depth: ........................... 310 mm
Weight: .......................................... approx. 13 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: .......................................... ≤ 1 mW
Protection class .......................................... III/
Minimum workpiece size: Only ever cut workpie-
ces which are big enough to clamp securely with
the clamping device – minimum length 160 mm.
This machine is equipped with a special precision
cut saw blade (cutting width 1.8 mm) for cordless
crosscut saws. If you use a diff erent saw blade
with a larger cutting width, this could result in loss
of performance.
This machine is intended for use with rechargea-
ble batteries and chargers from the Einhell Power-
X family only. For the current models, please refer
to the product descriptions for the articles. These
are available online.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
L sound pressure level ..................... 90.7 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ..................... 103.7 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Anl_TE_SM_36_210_Li_Solo_SPK9.indb 30
GB
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 General information
•
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
•
In the area of the machine's legs (34) there
is a fastening hole in each leg. Use them for
- 30 -
12.08.2020 10:51:05