EINHELL TE-SM 36/210 Li - Solo Instructions D'origine page 31

fastening standard screws, washers, spring
washers and nuts (not included in the scope
of this delivery - they are available from your
dealer). Fasten the machine on all four legs.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment's moving parts run
smoothly.
5.2 Assembling the saw (Figs. 1-9, 24)
•
Fasten the transport handle (9) to the machi-
ne head (4) using the screws (53).
•
Insert the screw (44) in the hole in the locking
screw (14) and position the combination key
(42) on the head of the screw.
•
Now fit the locking screw (14) to the shaft
(45), so that the screw (44) goes into the th-
readed hole. Fasten the locking screw (14) to
the shaft (45) by the screw (44).
•
Plug the cap (43) onto the locking screw (14).
•
Insert the guide pins of the adjustable workpi-
ece supports (47) into the mounting holes on
the machine housing.
•
To move the workpiece supports (47) to the
innermost position, actuate the lever (48) on
the underside of the workpiece support.
•
Tighten the stop screws (49) on the guide
rails in order to secure the workpiece sup-
ports against falling out.
•
To fit the sawdust bag (22) to the dust ext-
raction connector (51) on the crosscut saw,
spread the metal ring apart on the opening.
When the metal ring is back in its original
shape, the sawdust bag is held securely in
position.
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
Always fasten the clamping device (8) with
the locking screw (26).
•
For the horizontal clamping of workpieces you
can anchor the clamping device in the holder
(54).
•
Note: The combination key (42) should be
kept on the bask of the machine (see Fig. 24).
Anl_TE_SM_36_210_Li_Solo_SPK9.indb 31
GB
5.3 Adjusting the saw (Figs. 1-4, 9-10)
•
To adjust the turntable (17), loosen the lo-
cking screw (14) by approx. 2 turns, which
frees the turntable (17). Only then is it possi-
ble to adjust the turntable while holding the
release button (46) pressed down.
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the scale
(16).
•
The saw has locking positions at angles of -
45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°, 30° and
45°, at which the turntable (17) audibly clicks
into position. Once the turntable is engaged,
the setting must be additionally secured by
tightening the locking screw (14).
•
If different angle settings are required, the
turntable (17) may be secured in position
using only the locking screw (14).
•
To release the saw from its position at the
bottom, pull the retaining pin (25) out of the
motor mounting while pressing down lightly
on the machine head (4).
•
Swing up the machine head (4).
•
To move out the workpiece supports (47)
press the lever on the bottom side of the
workpiece support (48) and then pull the
workpiece support outwards to the right or
left.
•
For repeat cuts of identical length you can
unfold the longitudinal stop (50).
•
When the locking lever (21) is loosened, you
can tilt the machine head (4) to the left by up
to 45°. After the desired angular setting has
been set on the scale pointer (20) on the sca-
le (19), secure the machine head (4) again
with the locking lever (21).
•
To ensure that the saw is standing securely,
adjust the adjustable foot (13) by turning it so
that the saw stands in a horizontal and firm
position.
•
The machine head (4) can be moved back-
wards and forwards using the drag function.
To prevent the drag function, the guide rails
can be fixed in a specific position with the
locking screw (10).
5.4 Precision adjustment of the stop rail
(Fig. 11)
•
Lower the machine head (4) and fasten in
place with the retaining pin (25).
•
Fasten the turntable (17) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (7) and the stop rail (11).
•
Slacken the four adjustment screws (12)
using a hex key, set the stop rail (11) to 90° in
- 31 -
12.08.2020 10:51:05