Talk 2 All - Universal Intercom With Different Brand Unit; Compatibility With Midland Bt Line Units; Pairing The Midland Btx2 Pro To Bluetooth Devices; Background Feature - Midland BTX2 PRO Guide D'utilisation

Activate Conference mode
In "Intercom Mode" and no active audio, keep pressed the FWD and Middle buttons
for 3 sec. The voice announcement "Conference" will tell you that it is active.
When the Conference mode is active the "Phone" mode is not available because all the
devices paired on Vol+ and Vol – are temporary disconnected to guarantee the stability
of the conference mode.
Disable the "conference" mode
The conference mode can be disabled in every moment, just pressing the FWD and
Middle buttons for 3 sec. You will hear the voice announcement "Intercom" and from
that moment your Midland BTX2 PRO will start working with "one to one" intercom
and all the devices paired on Vol+ and Vol- are back, together with the "Phone" mode
and the "Talk2All-Universal intercom" feature.
Attention: when the "conference" mode is active, the "Talk2All- Universal Intercom" (to talk
with not Midland brand intercom) is not available.
Also if one unit was paired on the CTRL (middle) button, it is temporary unavailable,
you need to disable the "Conference" mode and go back to the standard "one to one"
Intercom mode.
How to use the conference mode
When the conference mode is active, is possible to open the intercom communication
pressing both the FWD and BWD button. One click on the button will open the inter-
com communication, one click on the same button will close it.
The two units that are in the middle of the chain (unit 2 and 3) must keep the intercom
open on both FWD and BWD button to allow the full communication of the four units
together.
"One Click Talk" function
When the conference mode is active, it is possible to open the intercom communica-
tion to all the 4 users just in "one click". Press short the CTRL (middle) button and you
will automatically open the conference to all the unit connected.
8

Talk 2 All - Universal Intercom with different brand unit.

Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to pair your
Midland BTX2 PRO to a different brand intercom available on the market.
You can pair a not Midland Intercom on the "Forward" button.
› On the Midland BTX2 PRO enter the setup mode: (with the unit OFF press and
hold down the Middle button about 7 sec. until the Red light is on permanently).
› Keep pressed the "Forward" button for 7 seconds: the Red and Blu LED light will
start flashing fast, then (while you still keep the button pressed) the Red and Blu
LED lights will change to slow flashing. Now you can stop pressing the button.
Talk2All - Universal Intercom
Not Midland Unit
On the other intercom (not Midland brand) follow the procedure to pair to a phone,
because the BTX2 PRO is paired as a Phone. If successfully paired the red/blue light
will stop flashing and the blu light will slowly flash instead.
Attention: remember to switch OFF all the other Bluetooth devices during the pairing pro-
cedure, only the two devices involved in the pairing must be turned on.
To open/close the "Universal Intercom" communication on the Midland
BTX2 PRO press very long (7 sec) in "Intercom" mode the Forward but-
ton. On the other intercom just press the phone redial or voice dial button.
Maybe it will be necessary to press the redial button two times, depending on the model
of the not Midland intercom.
Attention: In order to use the the "Talk2All-Universal Intercom" feature the pairing on the
other unit must be done as a phone. The other intercom (not Midland brand) will be able to
be paired to a phone only if two phones are supported.
You can pair also a Midland unit as Talk2All, that means the pairing must be done as a
phone (one unit use the Talk2All procedure and the other unit use the pairing to "Phone"
procedure).
www.midlandeurope.com

Compatibility with Midland BT line units

The BTX2 PRO is compatible with BTX1 PRO, BTNext PRO, BT Next Conference,
BTX2 FM and BTX2 FM.
When paired the max distance of the intercom is defined from the lower possible.
The BTX2 PRO is compatible with the previous line of Midland BT (BT Next, BTX2 and
BTX2) only if updated to firmware version 2014 or later.

Pairing the Midland BTX2 PRO to Bluetooth devices

The Midland BTX2 PRO unit can be paired to other Bluetooth devices, like Pho-
ne, GPS Navigator or PMR446 Radio with built-in or external Bluetooth (dongle).
The pairing procedure must be done using the "Volume +" or the "Volume -" buttons.
› Pairing to the "Volume +" button: for Phone with music A2DP stereo, GPS Naviga-
tor with A2DP audio or external mono/Stereo A2DP dongle.
› All devices paired to "Volume +" button have higher priority and will interrupt all the
other communications (like Intercom, FM Radio and Music).
› Pairing to the "Volume -" button: for a second phone with mono audio (Hands Free
Protocol) for GPS navigators/ Radar detector and other devices with mono audio.
MONO MONO and STEREO
› Phone (HFP Mono) › Phone (HFP/A2DP Stereo)
› GPS mono › GPS (HFP/A2DP Stereo)
› PMR446 Transceiver › Dongle (HFP/A2DP Stereo)
When a device is paired to the "Vol +" or "Vol –" buttons the "Phone" mode is acti-
vated.
Attention: A2DP audio source are supported only on Vol+. The second phone paired on
Vol- can support only mono audio (HFP).
www.midlandeurope.com

Background feature

It is possible to keep always in background the audio connection of the device paired
on "Vol-" button. In this way the Intercom communication will not be interrupted, for
example, by the GPS's street indication or or other audio mono device. To activate the
"Background" feature just press long the "Vol-" button, the voice "Background ON"
will tell you that now is active.
To deactivate the "Background" feature just press again long the "Vol-" button, the
voice "Background disable" will tell you that now is not active anymore.
By default the "Background" feature is off.

Pairing with one or two phones

The cellular phone can be paired to the "Vol +" (if the support for stereo A2DP is
requested) or to the "Vol –".
When a phone is paired to the "Vol +" or "Vol-" the "Phone" mode is activated.
An incoming call has always the higher priority, that means all other communications
will be closed (Intercom, FM Radio, Music).
If another incoming call will arrive on the second phone, an alert sound will notify it.
How to pair the Midland BTX2 PRO to a Phone
To pair the Midland BTX2 PRO to a Phone, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on per-
manently.
3. Now press for 3 seconds the "Volume +" or "Volume -" button, the Blue and Red
light will flash.
4. Enable the Bluetooth device search feature on your mobile phone
5. After some seconds, "Midland BTX2 PRO" will be displayed on your mobile phone.
Follow the pairing procedure of your Phone. If a pin code is requested you must
enter "0000" (four time zero).
When successfully paired, the Blue light of the unit will be on for one second and then
the unit will exit the setup mode and switch to the working mode (the Blue light will
start flashing).
You can use now your Midland BTX2 PRO together with the Phone.
9