Switching On And Off Your Midland Btx2 Pro; Operative "Mode; How To Pair Two Midland Btx2 Pro Units - Midland BTX2 PRO Guide D'utilisation

and that the white symbol is facing your mouth. This type of microphone is suited for
Open Faced and Flip Front helmets.
Wired microphone
Using the Velcro/adhesive strip, place the microphone inside the helmet in front of
your mouth. This type of microphone is more suited for Full Faced helmets. The mini
connector on the microphone allows you choose the microphone that best suits the
helmet you are using.
Description of the
Slide-in mounting kit
To fix the Midland BTX2 PRO onto the helmet, you have to install the slide-in moun-
ting kit by using the plate with bi-adhesive strip. This method allows you to safely "fix"
the BTX2 PRO unit onto your helmet and to remove it at any time in order to recharge
or store it.
Plate with bi-adhesive strip
The Bi-adhesive plate is already assembled on the slide-in mounting kit.
4
Bi-adhesive
Clean the application area on the helmet surface, remove the bi-adhesive film and pla-
ce the fixing plate on the left side of the helmet by keeping it contact with the surface
for a few seconds.
Fitting and removing your Midland BTX2 PRO
The BTX2 PRO can be easily fitted onto the helmet by sliding it downwards on the sli-
ding mounting kit. BTX2 PRO is maintained in position thanks to the fixing clip located
on the upper section (A). To detach the BTX2 PRO, simply press the fixing clip and
push the unit upwards.
Lock Unlock A

Switching ON and OFF your Midland BTX2 PRO

Switching the unit on:
Press and hold "Middle" button for approximately 3 seconds until the BLUE indicator
lights.
Switching the unit off:
Press and hold both "Middle" and "Backward" buttons together for approximately 3
seconds until the RED indicator flashes 3 times, thus lessening the chances that you
might turn off the unit accidentally (especially whilst wearing gloves).
www.midlandeurope.com

Operative "mode"

The BTX2 PRO can operate in three main "mode": Intercom, Phone and FM Radio.
The 3 multi function buttons can have different functionality depending on which mode
the unit is at that moment.
› In "Intercom mode" the three buttons let you manage the Intercom communica-
tions between driver and passenger or bike to bike.
› In "Phone mode" you can manage your Bluetooth mobile phone to place/answer a
phone call or to listen to the music or GPS App. announcement (in stereo mode).
Please use your phone responsibly and safely.
› In "FM Radio mode" you can listen to your favourite radio station in stereo, seek for
a specific radio station and save it (6 memories are available).
You can switch (toggle) from one mode to the other simply pressing the Middle button
for 3 seconds. A voice announcement will tell in which mode you are on.
The toggle sequence is the following:
› Intercom mode (if another unit has been paired)
› FM Radio
› Phone mode (if a phone has been paired)
Every time you turn on the unit, the default mode is the last used mode.
The Intercom mode and Phone mode are avalaible only if it was previously paired to
another unit or to a phone.
If you need to know in which mode the unit currently is, just press the "Volume + " and
"Volume –" buttons together. A voice announcement will tell you the current mode.
Maximum Distance
You can reach 1 Km intercom distance if you are in line of sight without obstructions
and interferences (the riders must be always in sight).
www.midlandeurope.com

How to pair two Midland BTX2 PRO units

The two units supplied in the same Midland BTX2 PRO box, are already paired and re-
ady to use, which mean you don't need to perform this procedure. The units are already
paired using the Middle button. If the devices are not part of the same kit, or the units
have been purchased separately, you need to first pair it in order to use it.
To pair the Midland BTX2 PRO to another Midland BTX2 PRO unit
To pair the Midland BTX2 PRO to another Midland BTX2 PRO unit, you must first enter
the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on per-
manently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will flash.
4. Do the same procedure on the other unit. When successfully paired, each unit will
have the Blue light on for one second and then go back to the setup mode (Red
light always on).
5. Now the pairing procedure is complete, you just need to exit the setup mode before
you can use the units.
6. Double click on the Middle button, the Red light will turn off and the Blue light will
start flashing.
You can use now your Midland BTX2 PRO
Attention: remember to switch off all the other Bluetooth device that are not part of the
pairing procedure, only the two devices involved in the pairing must be turned on.
How to use the Intercom with two units
To use the intercom feature, be sure that both units are turned on and correctly paired
together.
Manual activation
Press the Middle button on one of the two units in "Intercom" mode. Communication
is enabled and remains active until you press again the middle button. The intercom
need some seconds to activate, you will hear a beep tone when the intercom is open.
5